Airtac SE80 Standard Cylinder SE80X700
The AirTAC Airtac SE80 Standard Cylinder SE80X700 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 700mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke700 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X700
The AirTAC SE80X700 is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty automation. Operating at 0.7 MPa, it generates 3518 N of push force and 2268 N of pull force, utilizing a 25 mm piston rod and PT3/8 ports. Its square extruded aluminum barrel omits external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies sensor placement along three integrated grooves.
Because this specific SKU lacks the -S magnet code, it does not support direct CMSE or DMSE position sensing without modification. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when moving heavy loads at speeds up to 800 mm/s.
Airtac SE80 Standard Cylinder SE80X700 Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X700 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X700
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X700 Is Used
Pallet Transfer Diverters
Actuates heavy pallet diverter arms over a 700 mm stroke, relying on 3518 N of thrust at 0.7 MPa to reposition loaded conveyor lanes without mechanical binding.
Corrugated Box Presses
Drives the upper platen of a carton folding press, using its adjustable end cushions to soften the 2513 N stopping force and prevent crushing the cardboard structure.
Injection Mold Ejection
Pushes finished molded parts out of heavy tooling, where the robust 80 mm bore and 25 mm rod provide the rigidity needed to overcome part adhesion over a long cycle.
Is the Airtac SE80 Standard Cylinder SE80X700 the Right Cylinder?
Selecting the SE80X700 is appropriate when an application requires substantial thrust over a long 700 mm span. If 2513 N of push at 0.5 MPa is excessive, stepping down to the 63 mm bore yields 1559 N; conversely, moving up to the 100 mm bore provides 3927 N. As an ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for comparable standard cylinders, utilizing the same FA, FB, or TC mounting accessories and PT3/8 port threads.
With a 700 mm stroke, the 25 mm rod is subjected to significant bending moments under side loads. An external guide rail is strongly recommended to prevent rod-bearing wear and preserve alignment. Note that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking device. If the system must hold a vertical load without live air pressure, a BSE rod lock variant or external pilot-operated check valve is required.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X700 FAQ
The SE80X700 features an 80 mm bore, a 25 mm rod, and PT3/8 ports. At 0.5 MPa it provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa the push force is 3518 N, and the maximum push force is 513 kgf at 1.0 MPa.
Yes, the SE80X700 shares standard ISO 15552 / VDMA 24562 mounting dimensions, allowing it to serve as a drop-in replacement for other profile cylinders of the same bore size. It utilizes standard mounting accessories and a field-adjustable air cushion at both ends to fine-tune deceleration.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X700
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.