Airtac SE80 Standard Cylinder SE80X800
The AirTAC Airtac SE80 Standard Cylinder SE80X800 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 800mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke800 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X800
The AirTAC SE80X800 is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It generates 2513 N of push force and 2268 N of pull force at 0.5 MPa, utilizing an 80 mm bore and an 800 mm stroke. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing sensor grooves on three sides.
Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when moving heavy loads at speeds up to 800 mm/s. This SKU is built without a position sensor magnet, meaning it operates as a blind drive; adding an -S variant is necessary if CMSE or DMSE electronic switching is required for control feedback.
Airtac SE80 Standard Cylinder SE80X800 Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X800 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X800
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X800 Is Used
Palletizer Case Erector
Deploys the 2513 N push force and 800 mm stroke to square and seal large corrugated cardboard cases at the end of a packaging line.
Automated Stamping Press Loader
Transfers heavy steel blanks into a mechanical press, utilizing the 36 mm adjustable cushion to absorb kinetic energy at the extend stroke end.
Wood Panel Edge Bander
Applies consistent clamping pressure across long structural boards, relying on the tie-rod-free extruded profile for flush side mounting.
Is the Airtac SE80 Standard Cylinder SE80X800 the Right Cylinder?
Generating 2513 N of thrust at 0.5 MPa, this 80 mm bore is a robust mid-to-high range choice. If your application requires less force, stepping down to the 63 mm bore yields 1559 N of push at 0.5 MPa. Conversely, scaling up to the 100 mm bore provides 3927 N of push at 0.5 MPa for heavier payloads. Because the 800 mm stroke creates a long unsupported rod extension, an external guide bearing is strongly recommended to prevent rod-bearing bending and premature seal wear under side loads. As a true ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for other ISO 15552 cylinders, sharing standardized mounting accessories and a PT3/8 port. Note that this standard SE model will drift if air pressure is lost; it cannot hold a load in a centered or exhausted state without a BSE rod lock accessory.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X800 FAQ
At 0.5 MPa, the SE80X800 delivers 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force reaches 3518 N. The maximum permissible operating pressure is 1.0 MPa, which yields a maximum push of 513 kgf.
No, the SE80X800 is a standard double-acting cylinder and the piston will drift if air is exhausted or a valve is centered. The adjustable air cushion only decelerates the piston near the stroke ends; it does not lock or hold the load. For position holding, an external pilot-operated check valve or a BSE series rod lock is required.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X800
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.