Airtac SE80 Standard Cylinder SE80X80SCB
The AirTAC Airtac SE80 Standard Cylinder SE80X80SCB is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 80mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke80 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X80SCB
The AirTAC SE80X80SCB is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 2513 N of push force at 0.5 MPa. Fitted with a CB double clevis mounting eye, it is built for pivoting articulation in heavy dynamic assemblies. The extruded aluminum square barrel omits external tie rods, yielding a flush body that resists corrosion and simplifies bracket mounting in tight machinery frames.
This 80 mm bore unit includes a built-in magnet (-S) for position tracking with AirTAC CMSE reed and DMSE electronic sensors. The field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard mechanical impacts during high-speed cycling.
Airtac SE80 Standard Cylinder SE80X80SCB Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X80SCB |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 80 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X80SCB
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X80SCB Is Used
Palletizer Arm Actuation
Lifts and lowers palletizing gripper arms using 2513 N of push force, with the CB clevis accommodating the articulating sweep motion required for layer palletizing robots.
Stretch Wrap Film Carriage
Drives the vertical carriage of stretch wrap dispensers up and down a 80 mm stroke, utilizing the integrated magnet to trigger film overlap height limits via CMSE sensors.
Injection Mold Ejection
Provides 2268 N of retract force to pull heavy injection-molded automotive panels from dies, relying on the adjustable cushion to soften the mold-break shock.
Is the Airtac SE80 Standard Cylinder SE80X80SCB the Right Cylinder?
Delivering 2513 N push at 0.5 MPa, this 80 mm bore unit sits between the 63 mm class (1559 N push) and the 100 mm class (3927 N push), allowing you to step down for lower air consumption or up for heavier loads. The CB rear clevis mount is ideal for angular load movement. Note that a standard SE cylinder drifts when air is lost; if your pivoting mechanism must hold a suspended load without live pressure, step up to the BSE rod-lock variant. For this 80 mm stroke, side-load is minimal, but the 25 mm rod and M20x1.5 thread handle substantial bearing stress. To replace an existing ISO 15552 cylinder, match the 80 mm bore, 80 mm stroke, PT3/8 port, CB mounting accessory, and the -S magnet requirement.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X80SCB FAQ
At 0.5 MPa, the 80 mm bore provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force is 3518 N, with a maximum push capacity of 513 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE80X80SCB is dimensionally interchangeable per ISO 15552 standards, serving as a drop-in replacement for other ISO 15552 profile cylinders. It uses a PT3/8 port and includes a CB double clevis mount and a built-in magnet for CMSE/DMSE sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X80SCB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.