
The AirTAC SEJ Adjustable Cylinder SEJ32X150-20 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø32mm unit covers an effective stroke of 130–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X150-20 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window. A rod exits both ends, meaning the annulus area is identical in both directions, yielding an equal force of 345 N each way at 0.5 MPa. You can mechanically dial the retract end from 130mm up to the 150mm nominal stroke using a stop screw on the back rod.
This 32mm bore pneumatic cylinder operates at speeds from 30-800 mm/s and integrates adjustable air cushions at both ends to decelerate loads near stroke completion. The extruded aluminum barrel contains no external tie rods, ensuring clean ISO 15552 dimensional interchangeability. This specific SKU lacks a magnet, so it does not support CMSE or DMSE position sensing.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X150-20 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 20 mm (130–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 130-150mm retract stop to align a printing head, leveraging the 345 N both-way force to push and pull the carriage without speed variation.
Fine-tune a sheet-metal guide fence during commissioning, locking the back-rod stop screw precisely to the part width while the double-rod design resists side-load twisting.
Switch a 32mm bore packaging flap-folder between different carton heights by adjusting the stroke window, avoiding hardware swaps while maintaining 483 N at 0.7 MPa.
Confirm the 20mm adjustment window covers your required 130-150mm end-position range before ordering. If your application needs less force, the adjacent 32mm bore is the smallest standard size here, but stepping up to a 40mm bore yields 528 N both ways at 0.5 MPa. If your end position never changes, a fixed-stroke SED cylinder is sufficient. Remember that the adjustable cushion and mechanical stop screw decelerate the load but do not hold position on air loss; for fail-safe holding, use an external rod lock. When replacing an ISO 15552 cylinder, verify the PT1/8 port, M10x1.25 rod thread, and mounting subset (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The retract stroke is adjustable over a 20mm window via a mechanical stop screw on the back rod. The effective stroke range is 130mm to 150mm, which you set and lock during machine commissioning.
Because the rod exits both ends, force is equal in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.