
The AirTAC SEJ Adjustable Cylinder SEJ32X150-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø32mm unit covers an effective stroke of 120–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X150-30S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 30 mm adjustable stroke window. A stop screw on the back rod lets you dial the retract end, providing an effective stroke range of 120 to 150 mm for exact on-machine positioning. Because a rod exits both ends, the annular area is identical in both directions, yielding an equal force of 345 N each way at 0.5 MPa.
This 32 mm bore unit includes a magnet for CMSE reed and DMSE electronic sensors. It runs at 30-800 mm/s, uses a PT1/8 port, and features field-adjustable air cushions at both ends to decelerate the load near stroke end. The extruded aluminum barrel contains no external tie rods, ensuring clean ISO 15552 dimensional interchangeability.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X150-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 30 mm (120–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 120-150 mm retraction on a small pneumatic press, using the 345 N both-way force to seat components precisely without re-mounting hardware.
Adjust the retract stop by up to 30 mm to accommodate different part heights on a conveyor pick-and-place gripper, ensuring rapid machine changeover.
Micro-adjust the back-rod stop screw to true the final end position against a mechanical stop, leveraging the equal both-way force for consistent clamping.
This 30 mm adjustment window is ideal when you need to fine-tune a 120-150 mm end position during commissioning. If your application requires less force, there is no smaller bore in this series, but if you need to step up, the 40 mm bore provides 528 N both ways at 0.5 MPa. If your end position is fixed and never changes, a standard SED double-rod cylinder is sufficient. Remember that the adjustable cushion and stop screw only set the mechanical end and decelerate the load; they do not hold position on air loss. For fail-safe holding, use an external rod lock. At 150 mm stroke, side loads are minimal, but always guide the rod end to prevent binding.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 30 mm. This gives an effective stroke range of 120 to 150 mm. You lock the screw after setting your exact end position.
Because the rod exits both ends, force is equal in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.