
The AirTAC SEJ Adjustable Cylinder SEJ32X150-40 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø32mm unit covers an effective stroke of 110–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X150-40 is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas and an equal force of 345 N each way at 0.5 MPa. The retract stroke is mechanically adjustable via a stop screw on the back rod, providing a 40 mm dial-in window that sets the effective stroke range from 110 mm up to 150 mm.
This extruded-aluminum profile cylinder features field-adjustable air cushions at both ends to decelerate loads near the stroke terminus. Because this SKU lacks the -S magnet option, it does not support CMSE or DMSE position sensors. The back rod can also serve as a mounting point for a cam or external guide to help resist side loading.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X150-40 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 40 mm (110–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 110-150 mm retract stop to fine-tune sheet metal positioning during bending, using the equal 345 N both-way force to push and pull the gauge finger.
Adjust the back-rod stop screw up to 40 mm to rapidly switch carton folding heights between product runs without swapping out the entire cylinder hardware.
Commission a test fixture by tweaking the 40 mm window to find the exact 110-150 mm dispensing position before locking the stop screw for repeated cycles.
Verify the 40 mm adjustment window covers your required end-position range; if you need less fine-tuning, a fixed-stroke SED32X150 is sufficient. If sizing force, note the neighboring bores: step down to a 25 mm bore (not in this series) or up to a 40 mm bore delivering 528 N both ways at 0.5 MPa. For replacing an ISO 15552 unit, match the 32 mm bore, 150 mm stroke, PT1/8 port, and Basic/FA/LB/TC/FTC/TCM1/TCM2 mounting. A plain SEJ does not hold position on air loss; for fail-safe holding, specify a BSED or an external rod lock. Since the stroke is 150 mm, ensure external guides support any lateral load.
Quick checklist
The retract end features a stop screw with a 40 mm adjustment window, allowing the effective stroke to be dialed in anywhere from 110 mm to 150 mm. You set the exact end position on the machine and lock it in place.
Because the double-rod design creates equal annular areas, the force is identical in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.