
The AirTAC SEJ Adjustable Cylinder SEJ32X150-40S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø32mm unit covers an effective stroke of 110–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X150-40S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 40 mm adjustable stroke window. You can dial the retract end from 110 mm up to the nominal 150 mm, letting you fine-tune the end position directly on the machine without swapping hardware. A rod exits both ends, yielding identical annulus areas and an equal drive force of 345 N each way at 0.5 MPa.
This 32 mm bore unit includes a standard magnet for position sensing and uses a mechanical stop screw on the back rod to set the retract limit. It features field-adjustable air cushions at both ends to manage deceleration over the 27 mm cushion length. The extruded aluminum barrel ensures ISO 15552 dimensional interchangeability without external tie rods.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X150-40S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 40 mm (110–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 110-150 mm retract height for a fluid dispensing nozzle.
Adjust the retract stop on the fly when switching between 110 mm and 150 mm tall electronic enclosures on a conveyor line, avoiding the need to physically swap cylinders.
Use the back-rod stop screw to test multiple clamping depths on a light-duty machining fixture, locking the exact end position once the 345 N clamping force is verified.
Verify the 40 mm adjustment window covers your required positioning range. If your application requires more force, stepping up to the 40 mm bore yields 528 N both ways at 0.5 MPa. If the stroke never needs to change after commissioning, a fixed-stroke SED saves cost and length.
This cylinder uses a PT1/8 port and a 12 mm rod with an M10x1.25 thread. The adjustable air cushion decelerates the load near stroke end but does not lock the rod; for fail-safe position holding on air loss, use an external rod lock. At 150 mm stroke, side loads are minimal, but always guide the load externally to prevent rod binding.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 40 mm window. You can set the effective stroke anywhere from 110 mm up to the nominal 150 mm, then lock the screw in place.
Because it is a double-rod cylinder, the force is identical in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.