
The AirTAC SEJ Adjustable Cylinder SEJ32X150-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø32mm unit covers an effective stroke of 100–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X150-50 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so thrust is equal in both directions at 345 N each way at 0.5 MPa. You can dial the retract end from 100 to 150mm.
A stop screw on the back rod mechanically shortens the retract stroke over that fixed window, letting you fine-tune the end position directly on the machine without swapping hardware. The extruded aluminum barrel carries no external tie rods, and adjustable air cushions at both ends decelerate the 12mm rod near stroke ends. This SKU has no magnet, so it will not host CMSE or DMSE sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X150-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 50 mm (100–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Delivers 345 N of equal both-way force to seat small electronic connectors, using the 50mm stroke window to dial in the exact crush depth without reprogramming the machine controller.
Adjusts the retract stroke from 100 to 150mm to changeover a conveyor divertor arm for different package widths, locking the back-rod stop screw once the new end position is set.
Provides trial positioning for lab test fixtures, allowing operators to fine-tune the engagement distance of a 12mm rod against a specimen while maintaining symmetrical push and pull forces.
Verify the 50mm adjustment window covers your required end-position range. If 345 N at 0.5 MPa is too much, step down is not an option as 32mm is the smallest bore, but if you need more thrust, the next size up is the 40mm bore delivering 528 N each way at 0.5 MPa. If your stop position never changes, a fixed-stroke SED cylinder is sufficient.
Because the stroke is 150mm, external guides are recommended to manage side load. This plain SEJ does not hold position on air loss; the adjustable cushion and stop screw only set the mechanical end and decelerate, so for fail-safe holding point to a BSED or an external rod lock. For ISO 15552 replacement matching, confirm the 32mm bore, 150mm nominal stroke, 50mm window, PT1/8 port, and your mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2.
Quick checklist
The stroke adjusts over a 50mm window via a stop screw on the back rod. The effective retract stroke can be dialed down from the 150mm nominal maximum to 100mm, allowing precise end-position tuning on the machine.
Because the rod exits both ends, force is equal in both directions. It generates 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.