
The AirTAC SEJ Adjustable Cylinder SEJ63X250-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø63mm unit covers an effective stroke of 175–250mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X250-75S is a double-acting, double-rod ISO 15552 profile cylinder offering a 75 mm mechanical adjustment window. You can dial the retract end-position anywhere within an effective 175-250 mm range using the back-rod stop screw, then lock it down. This eliminates the need to swap physical hardware when fine-tuning machine stops.
Because a rod exits both ends, the annular area is identical in both directions, delivering an equal 1402 N of drive force each way at 0.5 MPa. The extruded aluminum barrel contains no external tie rods, and the included -S magnet enables precise end-of-stroke detection with CMSE reed or DMSE electronic sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X250-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 250 mm |
| Adjustment window | 75 mm (175–250 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×250 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 75 mm window to match varying die heights during press setups. The 1402 N both-way force at 0.5 MPa securely shifts heavy tooling without stroke hardware changes.
Adjust the retract stop on the fly to route different package sizes on a conveyor.
Fine-tune the 175-250 mm effective stroke to test sample contact points. The -S magnet pairs with DMSE electronic sensors for exact, repeatable data collection at each adjusted end.
Verify that your positioning tolerance fits inside the 75 mm retract window so you can exploit the full 175-250 mm effective range. If you need less force, stepping down to the 50 mm bore drops the both-way output to 825 N at 0.5 MPa; stepping up to the 80 mm bore raises it to 2268 N. If your end-position never changes after commissioning, a fixed-stroke SED provides the same double-rod symmetry without the adjustment hardware.
This cylinder uses a PT3/8 port and a Ø20 mm rod with an M16x1.5 thread. Since the 250 mm stroke exceeds 300 mm only marginally, ensure your external guides manage any side-load to protect the rod seals. Note that the adjustable air cushion and stop screw decelerate the load near stroke end but do not hold position on air loss; for fail-safe locking, specify an external rod lock.
AirtacDistr lists every SEJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sej63-adjustable-cylinder
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 75 mm window. You can set the effective stroke anywhere from 175 mm up to the full 250 mm, then lock the screw in place.
Because the rod exits both ends, force is equal in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.