
The AirTAC 4V220-06 Solenoid Valve, 4V200 Series (4V22006B-AM) is a genuine 5/2-way double solenoid (memory) solenoid valve with PT1/8 ports and an effective area of 17.0 mm² (Cv 1.0). It is an internally piloted spool valve that directs compressed air to double-acting cylinders and actuators.
The 4V22006B-AM is a 4V200-series double-solenoid 5/2 valve built for directing compressed air to double-acting cylinders and actuators. Because the spool has no return spring, it simply stays wherever it was last pulsed - held by land friction and balanced pressures, with no holding current - which makes it a natural fit for circuits where an actuator must keep its last position through a power cut. This version is fitted at the factory with an AMISCO (Italian) solenoid coil wired to a terminal box, running on a 24 V DC supply through standard PT (Rc) 1/8" ports.
Flow sits in the 17.0 mm2 effective area class (Cv 1.0), comfortably covering cylinders in the ~O32-50 mm bore range, and the valve responds in 0.05 s or less. The complete unit weighs 320 g. Note that the coil power rating for the AMISCO coil differs from the standard AirTAC coil, so confirm the exact W figure with us before ordering panel components.
| Model | AirTAC 4V220-06 Solenoid Valve, 4V200 Series (4V22006B-AM) |
|---|---|
| Series | 4V200 solenoid valve (spool type) |
| Valve type | 5/2-way |
| Function | Double solenoid (memory) |
| Port size | PT1/8 |
| Exhaust port | PT1/8 |
| Effective area (Cv) | 17.0 mm² (Cv 1.0) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Pilot type | Internal / external pilot |
| Operating pressure | 0.15 – 0.8 MPa |
| Proof pressure | 1.2 MPa |
| Max frequency | 5 cycle/sec |
| Response time | ≤ 0.05 s (activating) |
| Temperature | -20 to +70 °C |
| Body material | Aluminum alloy |
| Weight | 320 g |
Specifications follow the official AirTAC 4V series datasheet. Lubrication not required. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
| Effective area | 17.0 mm² |
|---|---|
| Flow coefficient | Cv 1.0 |
| Response time | ≤ 0.05 s |
| Coil power | AC 4.5 VA · DC24V 3.0 W · DC12V 2.5 W |
| Protection / insulation | IP65 (DIN40050), B-class |
| Voltage options | DC24V, DC12V, AC110V, AC220V |
| Manual override | Yes (locking / non-locking) |
Size the valve so effective area / Cv is not the bottleneck for your cylinder bore and speed. Undersized valves slow the actuator. Note 5/3 (center) versions have a smaller effective area than the 5/2 of the same body size.
| 4V | Solenoid valve, spool type, 4-series. |
|---|---|
| 2 | Body size (4V200) — sets port & flow. |
| 2 | Function: 1 = single 5/2, 2 = double 5/2, 3 = 5/3. |
| -06 | Port thread: M5 / 06=1/8" / 08=1/4" / 10=3/8" / 15=1/2". |
Related: 4V210 (single), 4V220 (double), 4V230C/E/P (5/3 center). Add the voltage suffix when ordering.
Pulse the two coils to run a double-acting cylinder that closes cartons or positions product; the valve keeps its last state through brief control-power dips, so the machine resumes without a homing step.
With 17.0 mm2 of effective area (Cv 1.0), the valve cycles double-acting clamping cylinders on ~O32-50 mm bores in assembly fixtures, holding the clamped or released state between pulses.
Drives product pushers and lane diverters where the actuator must not drift when the PLC output drops - the spool stays put without any holding current on the 24 V DC supply.
Choose this valve when your circuit needs position memory: a short pulse to one coil shifts the spool, and it remains there without power until the opposite coil is pulsed. If your cylinder is small (roughly O20 or below) and you do not need the wider 17.0 mm2 orifice, the 4V100 (Cv 0.6) is the lighter choice; for bores beyond ~O50 mm or high-speed cycles, step up to the 4V300 (Cv 1.65). If you would rather the actuator return automatically when the signal drops, pick a single-solenoid 5/2 instead; for mid-stroke holding, floating or pressurising, look at the 5/3 versions (Cv 0.8) in the same family. Single valves thread straight into the line, while a base-mounted layout lets several 4V200 units share one manifold block.
When replacing an existing unit, match all five points: body size (4V200), function (double solenoid), port plus thread (PT 1/8"), coil voltage (24 V DC) and electrical entry (terminal box). This -AM SKU also carries the AMISCO coil option, so spec the same suffix when swapping like for like.
Quick checklist
It is a double-solenoid 5/2 valve, so it is meant for double-acting cylinders and actuators only - single-acting types need a 3/2 valve. With an effective area of 17.0 mm2 (Cv 1.0, catalog figure for the 4V210-08) at PT 1/8" ports and 0.15-0.8 MPa working pressure, it suits cylinders of roughly O32-50 mm bore, cycling at up to 5 cycles per second with a response of 0.05 s or better.
The spool stays in whichever position the last coil pulse set it - held mechanically by land friction and balanced pressure, with no spring and no current needed; it is not a magnetically latched design. For suspended loads or true fall protection, add pilot-operated check valves at the cylinder ports or a mechanical brake rather than relying on the valve alone. The -AM suffix means the valve ships with an AMISCO (Italian) coil instead of the standard AirTAC coil on 24 V DC with a terminal box; body, ports and flow are unchanged, but ask us to confirm the exact AMISCO coil rating before sizing your power supply.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.