
The AirTAC 4V230C-06F Solenoid Valve, 5/3-way, closed center, PT1/8, DC12V, terminal entry (4V230C06F) is a genuine 5/3-way 5/3 double solenoid — closed center solenoid valve with PT1/8 ports and an effective area of 13.6 mm² (Cv 0.8). It is an internally piloted spool valve that directs compressed air to double-acting cylinders and actuators.
The AirTAC 4V230C-06F is a 5/3-way double-solenoid valve with a closed center, built on the 4V200 body. When both solenoids are de-energised, all five ports are blocked, trapping air on both sides of a double-acting cylinder to hold its position mid-stroke. This DC12V terminal-box model draws just 2.5 W, making it a low-power choice for battery-operated or mobile equipment that needs a mid-stop hold.
With an effective area of 13.6 mm² (Cv 0.8, catalog figure for the 4V230C-08) and a maximum cycling rate of 3 cycles per second, it suits ~O32-50 mm bore cylinders running at moderate speed. The spool shifts in 0.05 s or less, and the IP65-rated aluminium body stands up to dusty or washdown environments. For suspended loads, always pair the valve with a pilot-operated check valve or mechanical brake—the closed center alone is not a safety holding device.
| Model | AirTAC 4V230C-06F Solenoid Valve, 5/3-way, closed center, PT1/8, DC12V, terminal entry (4V230C06F) |
|---|---|
| Series | 4V200 solenoid valve (spool type) |
| Valve type | 5/3-way |
| Function | 5/3 double solenoid — Closed center |
| Port size | PT1/8 |
| Exhaust port | PT1/8 |
| Effective area (Cv) | 13.6 mm² (Cv 0.8) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Pilot type | Internal / external pilot |
| Operating pressure | 0.15 – 0.8 MPa |
| Proof pressure | 1.2 MPa |
| Max frequency | 3 cycle/sec |
| Response time | ≤ 0.05 s (activating) |
| Temperature | -20 to +70 °C |
| Body material | Aluminum alloy |
| Weight | 360 g |
Specifications follow the official AirTAC 4V series datasheet. Lubrication not required. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
| Effective area | 13.6 mm² |
|---|---|
| Flow coefficient | Cv 0.8 |
| Response time | ≤ 0.05 s |
| Coil power | AC 4.5 VA · DC24V 3.0 W · DC12V 2.5 W |
| Protection / insulation | IP65 (DIN40050), B-class |
| Voltage options | DC24V, DC12V, AC110V, AC220V |
| Manual override | Yes (locking / non-locking) |
Size the valve so effective area / Cv is not the bottleneck for your cylinder bore and speed. Undersized valves slow the actuator. Note 5/3 (center) versions have a smaller effective area than the 5/2 of the same body size.
| 4V | Solenoid valve, spool type, 4-series. |
|---|---|
| 2 | Body size (4V200) — sets port & flow. |
| 3 | Function: 1 = single 5/2, 2 = double 5/2, 3 = 5/3. |
| -06 | Port thread: M5 / 06=1/8" / 08=1/4" / 10=3/8" / 15=1/2". |
Related: 4V210 (single), 4V220 (double), 4V230C/E/P (5/3 center). Add the voltage suffix when ordering.
A 5/3 closed-center valve stops a clamp cylinder partway through its stroke and holds pressure on both sides, keeping the workpiece in place during a two-stage machining or gluing operation.
On a packaging line, the 4V230C-06F halts a vertical lift cylinder mid-travel to allow a label to be applied. The closed center prevents the load from sinking while the label is pressed on.
A test fixture uses the valve to move a probe to a precise intermediate position and hold it there for a measurement cycle. The 2.5 W DC12V coil keeps heat low inside the compact instrument enclosure.
Choose the 4V230C-06F when your application requires the actuator to pause and hold position at mid-stroke. The closed center blocks inlet and exhaust, so the cylinder resists external forces better than an exhaust-center valve. If you only need end-to-end motion, the simpler 5/2 single (4V210) or double (4V220) saves cost and gives a higher Cv of 1.0.
For a direct replacement, match all five points: body size 4V200, function 30C (5/3 closed center), 1/8in PT port, DC12V coil voltage, and terminal-box electrical entry. If your cylinder bore is below O25, step down to the 4V100 series (Cv 0.6) for better low-flow control. For bores above O63 or faster cycle times, the 4V300 series (Cv 1.65) provides the extra flow.
Quick checklist
With an effective area of 13.6 mm² (Cv 0.8, catalog figure for the 4V230C-08), it is well matched to double-acting cylinders in the O32-50 mm bore range for general industrial speeds. Smaller cylinders will cycle very fast; larger bores will move more slowly. If you need a faster cycle on a O63 or larger cylinder, consider moving up to the 4V300 series (Cv 1.65).
The closed center blocks all ports, trapping air on both sides of the piston to resist motion from balanced external forces. However, it is not a safety-rated holding device—air can leak past the spool and seals over time. For a suspended or vertical load.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity, coil voltage and destination. We confirm price, stock and lead time — usually within 7-8 hours.