Airtac SE50 Standard Cylinder SE50AX600S
The AirTAC SE50 Standard Cylinder SE50AX600S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 600mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ50 mm
- Stroke600 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE50 Standard Cylinder SE50AX600S
The AirTAC SE50AX600S is a double-acting single-rod ISO 15552 profile cylinder engineered for a 50mm bore and 600mm stroke. It delivers 982 N of push force and 825 N of pull force at 0.5 MPa, peaking at 1374 N push at 0.7 MPa. The extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against frames while resisting corrosion.
This specific configuration pairs a SUS420J2 stainless steel rod (code A) for washdown and corrosive-duty environments with a built-in magnet (code S) for position tracking. The integrated magnet interfaces directly with AirTAC CMSE reed and DMSE electronic sensors seated in the three-sided sensor grooves. Field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration to soften hard impacts at operating speeds up to 800 mm/s.
Airtac SE50 Standard Cylinder SE50AX600S Technical Specifications
| Model | Airtac SE50 Standard Cylinder SE50AX600S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE50 Standard Cylinder SE50AX600S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE50 Standard Cylinder SE50AX600S Is Used
Flow Wrapper Infeed Pusher
Drives the infeed pusher on a stainless-steel flow wrapper at 600mm stroke, where the SUS420J2 rod withstands washdown and the 982 N push force at 0.5 MPa easily overcomes packaging film friction.
Pallet Transfer Diverter
Actuates a 600mm diverter arm on a pallet transfer line, using the built-in magnet to trigger DMSE electronic sensors for precise mid-stroke positioning before routing.
Lab Washdown Ejector
Ejects processed samples from a laboratory washdown station, relying on the corrosion-resistant SUS420J2 rod and adjustable end cushions to handle rapid 800 mm/s ejection cycles smoothly.
Is the Airtac SE50 Standard Cylinder SE50AX600S the Right Cylinder?
If your application requires less force, stepping down to the 40mm bore drops the 0.5 MPa push to 628 N, whereas stepping up to the 63mm bore increases it to 1559 N. Because this is a 600mm stroke, the unsupported rod length increases bending moments on the rod bearing under side loads; an external guide rail is strongly recommended to prevent premature seal wear. As a standard ISO 15552 cylinder, it serves as a dimensionally interchangeable direct replacement for competing ISO 15552 profile cylinders, utilizing the same PT1/4 port, M16x1.5 rod thread, and shared mounting hardware. Note that this cylinder relies on live air pressure to move; the adjustable cushion only decelerates the piston near stroke end and will not hold a load if air is exhausted.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE50 Standard Cylinder SE50AX600S FAQ
The SE50AX600S generates 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and a maximum push of 200 kgf at 1.0 MPa. It uses a PT1/4 port and a 20mm rod with an M16x1.5 thread.
No, the SE50AX600S is a standard double-acting cylinder and the piston will drift if air is lost or the valve is centered. The adjustable air cushions at both ends only decelerate the piston near the stroke ends; they do not lock or hold the load. For position holding, consider an AirTAC BSE series rod lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE50 Standard Cylinder SE50AX600S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.