
The AirTAC SE50 Standard Cylinder SE50AX80 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 80mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50AX80 is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa. Its 80 mm stroke is governed by a Ø20 mm rod with an M16x1.5 thread, utilizing a PT1/4 port for pneumatic supply. Because it uses a square extruded aluminum barrel without external tie rods, the body is highly compact, corrosion-resistant, and mounts flush against machine frames.
This specific SKU features an SUS420J2 stainless steel rod (material code A) tailored for corrosive or washdown environments. It lacks a built-in magnet, meaning it does not support CMSE or DMSE position sensors out of the box. Field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s.
| Model | Airtac SE50 Standard Cylinder SE50AX80 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 80 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the 80 mm stroke sealing jaw on continuous motion flow wrappers, where the 982 N push force securely crimps film seams and the SUS420J2 rod shrugs off daily washdowns.
Indexes pneumatic sorting gates on parcel conveyor lines, relying on the compact tie-rod-free extruded profile to mount flush in tight transfer zones.
Automates process valves on clean-in-place skids for dairy filling machines, leveraging the stainless steel rod material to endure caustic cleaning chemicals.
If 982 N of push at 0.5 MPa is too much for your payload, step down to the 40 mm bore which yields 628 N. Conversely, if your fixture requires heavier clamping, step up to the 63 mm bore providing 1559 N. As a standard ISO 15552 profile cylinder, this unit is dimensionally interchangeable with other ISO 15552 cylinders, allowing you to reuse existing mounting hardware like FA front flanges or LB foot brackets. Keep in mind a plain SE cylinder relies on live air pressure to hold position; if your process loses air, the piston will drift. For positive holding without pressure, consider the BSE rod lock variant.
Quick checklist
At 0.5 MPa, the SE50AX80 generates 982 N of push force and 825 N of pull force. At 0.7 MPa, push force increases to 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
This specific SE50AX80 SKU lacks a built-in magnet, so it cannot support AirTAC CMSE or DMSE electronic sensors without modification. Dimensionally, it is a true ISO 15552 profile cylinder, meaning it serves as a direct replacement for any standard ISO 15552 mounting footprint.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.