Airtac SE50 Standard Cylinder SE50BX100SN
The AirTAC SE50 Standard Cylinder SE50BX100SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 100mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ50 mm
- Stroke100 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE50 Standard Cylinder SE50BX100SN
The AirTAC SE50BX100SN is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding washdown and corrosive environments. By utilizing a SUS304 stainless steel rod and NBR seal, it reliably generates 982 N of push force at 0.5 MPa (1374 N at 0.7 MPa) across its 100 mm stroke. The square extruded aluminum barrel omits external tie rods, yielding a compact, flush-mounting body that naturally resists dirt accumulation and simplifies fixture integration.
Designed for precise end-position sensing, this variant includes a built-in magnet (-S) compatible with AirTAC CMSE reed and DMSE electronic sensors. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration for moving loads, ensuring smooth operation within its 30-800 mm/s speed range.
Airtac SE50 Standard Cylinder SE50BX100SN Technical Specifications
| Model | Airtac SE50 Standard Cylinder SE50BX100SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE50 Standard Cylinder SE50BX100SN
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE50 Standard Cylinder SE50BX100SN Is Used
Flow Wrapper Sealing
Drives the sealing jaw on continuous motion flow wrappers, using the 982 N extend force and 100 mm stroke to cleanly cut and seal packaging films at high cycle rates.
Bottling Line Diverter
Actuates stainless-steel guide rails on beverage bottling conveyors, where the SUS304 rod withstands frequent washdowns and moisture exposure without degrading.
Pneumatic Press Standby
Provides steady clamping pressure for light-duty assembly stations, using its adjustable pneumatic cushioning to prevent shock loads when retracting the 20 mm rod.
Is the Airtac SE50 Standard Cylinder SE50BX100SN the Right Cylinder?
Generating 982 N of push force at 0.5 MPa, this 50 mm bore sits perfectly between the 40 mm bore (628 N push) for lighter duties and the 63 mm bore (1559 N push) for heavier payloads. If your application requires holding a load vertically without live air pressure, note that a standard SE cylinder will drift; you should evaluate the BSE rod-lock variant or an external pilot-operated check valve. For retrofitting, this model provides direct dimensional interchangeability with any ISO 15552 cylinder, utilizing a PT1/4 port, M16x1.5 rod thread, and standard mounting accessories.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE50 Standard Cylinder SE50BX100SN FAQ
At 0.5 MPa, the SE50BX100SN provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force is 1374 N. The maximum push force is 200 kgf at 1.0 MPa, and it operates at speeds between 30-800 mm/s.
Yes, the SE50BX100SN is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting footprint and pin dimensions of other ISO 15552 profile cylinders. You can drop it into existing mounts using standard accessories, provided your system matches its PT1/4 port and M16x1.5 rod thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE50 Standard Cylinder SE50BX100SN
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.