
The AirTAC SE50 Standard Cylinder SE50BX125S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 125mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50BX125S is a double-acting ISO 15552 profile cylinder engineered for rigorous washdown and corrosive environments. By utilizing a SUS304 stainless steel piston rod, it resists rust where standard carbon steel fails, while delivering a robust 982 N push force at 0.5 MPa. Its extruded aluminum barrel omits external tie rods, yielding a sleek, flush-mount profile that prevents debris accumulation.
This 50 mm bore unit includes a built-in magnetic piston (-S) designed to interface directly with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune deceleration via a set screw, softening hard mechanical impacts during high-speed operations.
| Model | Airtac SE50 Standard Cylinder SE50BX125S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 125 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×125 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Routes stainless steel containers on a washdown line using the 982 N push force and SUS304 rod to withstand harsh chemical sprays.
Drives the sealing jaw with a 125 mm stroke, relying on the -S magnet and DMSE electronic sensors to confirm jaw closure timing.
Actuates a sorting flap in high-salinity environments, leveraging the corrosion-resistant SUS304 rod and tie-rod-free profile to prevent bacteria traps.
When sizing this 982 N (push at 0.5 MPa) actuator, you can step down to the 40 mm bore if your load requires only 628 N, or step up to the 63 mm bore for 1559 N of thrust. To achieve a direct replacement per ISO 15552 mounting interface dimensions, match the 50 mm bore, 125 mm stroke, PT1/4 port, and your specific mounting accessory. Because the stroke is 125 mm, side-load stress on the rod bearing is moderate, but ensure the load is guided externally to prevent premature seal wear. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not lock or hold the load if air pressure is lost.
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N. The maximum push force is 200 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE50BX125S is dimensionally interchangeable per ISO 15552 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders with a 50 mm bore, 125 mm stroke, and PT1/4 port, sharing the same standardized mounting hardware.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.