
The AirTAC SE50 Standard Cylinder SE50BX150 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 150mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50BX150 is a double-acting single-rod ISO 15552 profile cylinder featuring a 50 mm bore and 150 mm stroke. It generates 982 N of push force and 825 N of pull force at 0.5 MPa, making it well-suited for mid-range industrial actuation. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This specific SKU utilizes a SUS304 stainless steel piston rod (option B) engineered for corrosive environments and washdown duty. It lacks a built-in position magnet, meaning no CMSE or DMSE sensors can be attached to this specific unit. Field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed cycling.
| Model | Airtac SE50 Standard Cylinder SE50BX150 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the sealing jaws on vertical form-fill-seal pouch machines, where the SUS304 rod withstands daily washdown chemistry and the 982 N push force securely crimps packaging film.
Actuates a routing flap on a stainless conveyor handling raw poultry, using the 150 mm stroke to shift product lanes while resisting high-moisture corrosion.
Powers the safety latch on an industrial lab centrifuge, applying 825 N of pull force at 0.5 MPa to hold the high-speed rotor shield closed during operation.
Selecting this 50 mm bore yields 982 N push at 0.5 MPa. If your assembly requires less force, the 40 mm neighbor provides 628 N; if your payload is heavier, stepping up to the 63 mm bore provides 1559 N. Because this plain SE cylinder does not hold its position or load when air is lost, exhausted, or the valve is centered, you must integrate an external rod lock or pilot-operated check valve for fail-safe load holding.
To replace an existing cylinder, match the 50 mm bore, 150 mm stroke, PT1/4 port, and required mounting accessory (such as LB foot or FA front flange). Note that this SKU lacks the -S magnet, so it cannot support CMSE or DMSE position switches without changing the configuration. With a 150 mm stroke, the unsupported load is relatively short, but always verify the rod-bearing bending loads if side forces are present.
Quick checklist
At 0.5 MPa, the SE50BX150 provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force is 1374 N. The maximum push force is 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE50BX150 is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting footprint, PT1/4 port, and M16x1.5 rod thread of other ISO 15552 profile cylinders. It is a direct replacement for standardized hardware.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.