
The AirTAC SE50 Standard Cylinder SE50BX400SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 400mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50BX400SH is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding washdown and high-temperature environments. Delivering 982 N of push force at 0.5 MPa over a 400 mm stroke, it utilizes a SUS304 stainless steel rod and FKM Viton seals to operate reliably up to 150 C. The extruded aluminum barrel lacks external tie rods, presenting a smooth, corrosion-resistant exterior that mounts flush against machine frames.
This model includes a built-in magnet (-S) for non-contact position sensing using AirTAC CMSE reed or DMSE electronic switches. To protect the end caps and tooling, field-adjustable air cushions at both ends allow technicians to dial in the exact deceleration rate required to soften hard end stops at high cycling speeds up to 800 mm/s.
| Model | Airtac SE50 Standard Cylinder SE50BX400SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 400 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Utilizing the FKM Viton seals rated for 150 C and the SUS304 rod, this cylinder pushes 400 mm to extract hot baked goods trays from continuous ovens without degrading.
Providing 982 N of extend force at 0.5 MPa, it actuates heavy gauge metal forming clamps that must withstand high ambient heat and washdown chemicals.
The smooth, tie-rod-free extruded profile prevents contaminant buildup while the DMSE electronic sensors confirm 400 mm retraction on clean-in-place valve panels.
When sizing this 50 mm bore actuator, evaluate stepping down to a 40 mm bore (628 N push at 0.5 MPa) for lighter loads, or up to a 63 mm bore (1559 N push at 0.5 MPa) if your payload demands higher thrust. Because this is a 400 mm stroke, the unsupported rod length increases bending moments on the rod bearing; for heavy offset loads, integrate an external guide rail to prevent premature wear. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other ISO 15552 cylinders, sharing standard mounting accessories, PT1/4 ports, and the M16x1.5 rod thread. Remember that the adjustable cushion only decelerates the piston near stroke end and will not hold a load if air pressure is lost.
Quick checklist
At 0.5 MPa, the push force is 982 N and the pull force is 825 N. At 0.7 MPa, the push force is 1374 N. The maximum push force is 200 kgf when operating at the maximum rated pressure of 1.0 MPa.
Yes. The SE50BX400SH is configured with a SUS304 stainless steel rod (code B) and FKM Viton seals (code H), expanding the operating temperature range to 150 C for corrosive washdown duty.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.