Airtac SE50 Standard Cylinder SE50BX700SH
The AirTAC SE50 Standard Cylinder SE50BX700SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 700mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ50 mm
- Stroke700 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE50 Standard Cylinder SE50BX700SH
The AirTAC SE50BX700SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for rigorous washdown and high-temperature duty. It yields 982 N of push force at 0.5 MPa and utilizes a SUS304 stainless steel rod alongside a Viton (FKM) seal, widening the operating temperature range up to 150 C.
Its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that simplifies mounting. The integrated magnet (-S) directly supports AirTAC CMSE reed and DMSE electronic position sensing, while the field-adjustable pneumatic cushioning at both ends lets you precisely tune end-of-stroke deceleration for heavy 700 mm traverses.
Airtac SE50 Standard Cylinder SE50BX700SH Technical Specifications
| Model | Airtac SE50 Standard Cylinder SE50BX700SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE50 Standard Cylinder SE50BX700SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE50 Standard Cylinder SE50BX700SH Is Used
Bottling Line Diverters
Actuates routing gates on beverage lines, using the 982 N thrust and SUS304 rod to withstand daily chemical washdowns without pitting.
Thermoforming Ejectors
Pushes hot molded plastic parts clear of the mold cavity, leveraging the 150 C Viton seal to maintain integrity near radiant heat sources.
Palletizer Push-Arms
Transfers layered product across a 700 mm span, relying on the adjustable end cushions to soften stops and protect the load from sudden impacts.
Is the Airtac SE50 Standard Cylinder SE50BX700SH the Right Cylinder?
This 50 mm bore provides 982 N push at 0.5 MPa. If your application requires less thrust, stepping down to the 40 mm bore drops output to 628 N; conversely, moving up to the 63 mm bore increases thrust to 1559 N. Because this is a 700 mm stroke, the unsupported piston rod is highly susceptible to bending under side loads—always incorporate an external guide rail to prevent rod-bearing damage.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other ISO 15552 cylinders, matching the 50 mm bore, 700 mm stroke, PT1/4 port, and standard mounting accessories. Note that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load if air pressure is lost. For position holding, consider a BSE rod lock or external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE50 Standard Cylinder SE50BX700SH FAQ
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552, allowing a direct replacement for other ISO 15552 cylinders using the same mounting hardware and PT1/4 ports. However, it cannot hold a load without live air pressure; the adjustable cushion only decelerates the piston near the end of its stroke and acts as no lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE50 Standard Cylinder SE50BX700SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.