verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE50 Standard Cylinder SE50X10

The AirTAC SE50 Standard Cylinder SE50X10 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 10mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ50 mm
  • Stroke10 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 30 mm
$63.70 $71.20Save 10% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE50 stroke, mounting and version on one page All SE50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE50 Standard Cylinder SE50X10

The AirTAC SE50X10 is a double-acting single-rod ISO 15552 profile cylinder engineered for short-stroke actuation, delivering a push force of 982 N and pull force of 825 N at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. This clean profile simplifies retrofitting into tight assemblies where space is at a premium.

Because this specific SKU lacks the -S magnet suffix, it does not support direct CMSE or DMSE position sensing without modification. The cylinder relies on field-adjustable pneumatic cushioning at both ends to decelerate the payload smoothly. This cushioning uses a needle screw to tailor the exhaust restriction, softening the end-of-stroke impact rather than acting as a fixed rubber bumper.

Airtac SE50 Standard Cylinder SE50X10 Technical Specifications

ModelAirtac SE50 Standard Cylinder SE50X10
SeriesSE ISO 15552 profile cylinder
Bore sizeØ50 mm
Stroke10 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø50mm)

PressurePush forcePull force
0.5 MPa982 N825 N
0.7 MPa1374 N—
Max (@1.0 MPa)200 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE50 Standard Cylinder SE50X10

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
50Bore size in mm.
×10Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE50 Standard Cylinder SE50X10 Is Used

precision_manufacturing

Stamping Pin Ejection

Uses the 982 N extend force to eject small stamped metal pins from a die plate in a high-speed press line, relying on the 10 mm stroke for rapid cycling.

packaging

Carton Flap Folding

Deploys the short 10 mm stroke to tuck inner corrugated flaps on a packaging conveyor before tape application, fitting neatly into compact guide rails.

science

Lab Dispenser Clamping

Secures low-profile fluid dispenser bottles in a laboratory automation cell, using the 825 N retract force to pull a lightweight stopper plate into position.

Is the Airtac SE50 Standard Cylinder SE50X10 the Right Cylinder?

When sizing this 50 mm bore actuator, compare its 982 N push force against your actual load requirements. If you need less force and a smaller footprint, stepping down to the 40 mm bore yields 628 N of push at 0.5 MPa. Conversely, if your load demands more thrust, stepping up to the 63 mm bore provides 1559 N at 0.5 MPa. This SE50X10 ships with a PT1/4 port and a 20 mm piston rod.

Remember that a standard double-acting cylinder drifts when air pressure is lost or the valve is centered; the adjustable air cushion only decelerates the piston near stroke end and does not lock the load. If your application requires position holding without live pressure, consider the BSE rod-lock variant. For this 10 mm stroke, side-load stress on the rod bearing is minimal, but external guides are always recommended for heavy lateral loads.

AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE50 Standard Cylinder SE50X10 FAQ

The SE50X10 delivers a push force of 982 N and a pull force of 825 N at 0.5 MPa. At 0.7 MPa, the push force increases to 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.

Yes, it is dimensionally interchangeable with other ISO 15552 profile cylinders for direct retrofits. However, because this specific SKU lacks the -S magnet code, it cannot host CMSE or DMSE position sensors out of the box; you would need a magnet-equipped variant for electronic or reed switch feedback.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE50 Standard Cylinder SE50X10

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE50X10 and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.