Airtac SE50 Standard Cylinder SE50X160SCBCR
The AirTAC SE50 Standard Cylinder SE50X160SCBCR is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 160mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ50 mm
- Stroke160 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE50 Standard Cylinder SE50X160SCBCR
The AirTAC SE50X160 is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. This design simplifies retrofitting into existing ISO 15552 footprints without special brackets.
Equipped with a built-in magnet for CMSE and DMSE position sensing, this unit allows precise end-of-stroke detection. The field-adjustable air cushioning at both ends can be tuned via a set screw to soften hard end stops at speed, protecting payloads during the 160 mm travel.
Airtac SE50 Standard Cylinder SE50X160SCBCR Technical Specifications
| Model | Airtac SE50 Standard Cylinder SE50X160SCBCR |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 160 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE50 Standard Cylinder SE50X160SCBCR
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE50 Standard Cylinder SE50X160SCBCR Is Used
Carton Flap Folding
Applies the 982 N push force required to fold heavy corrugated cardboard flaps on high-speed packaging lines prior to sealing.
Pallet Diverting Gate
Uses the 160 mm stroke and CB clevis mount to pivot a routing gate smoothly, redirecting pallets between conveyor lanes.
Press Roller Adjustment
Actuates a rubber press roller in a textile mill, relying on DMSE electronic sensors to confirm precise material engagement.
Is the Airtac SE50 Standard Cylinder SE50X160SCBCR the Right Cylinder?
This 50 mm bore provides 982 N push at 0.5 MPa, sitting neatly between the 40 mm bore (628 N) for lighter fixtures and the 63 mm bore (1559 N) for heavier demanding loads. The included CB double clevis mounting accessory is ideal for pivoting articulations. Because the stroke is 160 mm, side-load stress on the rod bearing remains moderate, though an external guide is always recommended for heavy off-center loads.
As a standard double-acting cylinder, the SE50X160 will drift if air pressure is lost or the valve centers; it cannot hold a load mid-stroke. For suspended loads requiring safety locking, consider the BSE rod-lock variant. To replace an existing unit, match the 50 mm bore, 160 mm stroke, PT1/4 port, and CB mount.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE50 Standard Cylinder SE50X160SCBCR FAQ
At 0.5 MPa, the push force is 982 N and the pull force is 825 N. At 0.7 MPa, the push force increases to 1374 N. The maximum rated push force is 200 kgf at 1.0 MPa.
Yes, the SE50X160 is dimensionally interchangeable per ISO 15552. You can drop it in to replace other ISO 15552 profile cylinders by matching the 50 mm bore, 160 mm stroke, PT1/4 port, and CB mounting interface.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE50 Standard Cylinder SE50X160SCBCR
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.