
The AirTAC SE50 Standard Cylinder SE50X190FTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 190mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X190FTC is a double-acting, single-rod ISO 15552 profile cylinder engineered for precise linear actuation. It generates 982 N of push force at 0.5 MPa and 1374 N at 0.7 MPa, utilizing a 50 mm bore and 190 mm stroke. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This specific SKU is configured with an FTC mounting accessory and lacks the built-in magnet option, meaning it operates without position sensing unless external switches are retrofitted. Field-adjustable pneumatic cushioning at both stroke ends allows technicians to dial in the deceleration rate, softening end-stop impacts at high cycle speeds without relying on fixed rubber bumpers.
| Model | Airtac SE50 Standard Cylinder SE50X190FTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 190 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×190 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folding mechanism on continuous-motion carton erectors, utilizing the 190 mm stroke to clear the package path while delivering 982 N to snap heavy cardboard flaps into position.
Pivots routing gates on parcel sortation conveyors, where the FTC mount provides a rigid pivot axis and the extruded profile barrel withstands dusty logistics hub environments.
Actuates the sliding safety door on CNC turning centers, relying on the field-adjustable cushions to prevent harsh slamming that could skew machine alignment.
Selecting this 50 mm bore makes sense when your load requires the 982 N push available at 0.5 MPa. If your application is lighter, stepping down to the 40 mm bore yields 628 N of push, whereas heavier loads demand the 63 mm bore providing 1559 N. Because this model lacks the -S magnet code, it cannot host CMSE or DMSE sensors natively; if your sequence control requires end-of-stroke confirmation, specify an SE50X190SFTC instead.
The 190 mm stroke falls below the 300 mm threshold where severe rod-bearing bending typically mandates an external guide, but maintaining adequate side-load support remains best practice. Remember that the adjustable air cushion only decelerates the piston near the end of travel; it does not lock the rod. If power or air is lost, the load will drift, requiring a BSE rod lock for secure holding.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The SE50X190FTC provides a push force of 982 N and a pull force of 825 N at 0.5 MPa. At 0.7 MPa, the push force is 1374 N, and the maximum push force is 200 kgf at 1.0 MPa. It operates at speeds ranging from 30 to 800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552 standards, serving as a direct replacement for other ISO 15552 profile cylinders using the FTC mounting interface. However, the adjustable air cushion only decelerates the piston near stroke end; it does not hold the load. If air is lost, the piston drifts, so a BSE rod lock is needed for position holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.