
The AirTAC SE50 Standard Cylinder SE50X280S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 280mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X280S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa (1374 N at 0.7 MPa) across a 280 mm stroke. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal components from workshop debris.
Because this specific unit includes the built-in magnet (-S), it is fully primed for non-contact position sensing using AirTAC CMSE reed or DMSE electronic switches that drop directly into the body's three-sided sensor grooves. Furthermore, the end caps house field-adjustable pneumatic cushioning, allowing technicians to tune the deceleration of the 20 mm hard-chrome rod via a set screw to soften hard end stops during high-speed cycling.
| Model | Airtac SE50 Standard Cylinder SE50X280S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 280 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×280 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Utilizes the 982 N push force at 0.5 MPa to rapidly actuate routing flaps on a packaging conveyor, while the -S magnet triggers DMSE electronic sensors to confirm gate position for the PLC.
Extends 280 mm to push bar stock into a lathe collet, relying on the adjustable air cushion to decelerate the 20 mm rod smoothly and prevent jaw damage during high-speed automated loading.
Employs the extruded no-tie-rod profile for flush side-mounting in tight palletizing cells, using its 825 N pull force to retract a carton pusher without snagging on adjacent framework.
When sizing this 50 mm bore actuator, evaluate your exact thrust margins: the neighboring 40 mm bore provides 628 N of push at 0.5 MPa, while stepping up to the 63 mm bore yields 1559 N. If your load demands 982 N at 0.5 MPa but requires position holding or fail-safe braking when air pressure is lost, remember that the standard SE cylinder will drift; you must pivot to the BSE series (rod lock) or utilize an external pilot-operated check valve.
To replace an existing actuator, verify the 280 mm stroke, PT1/4 porting, and M16x1.5 rod-end thread. Because this model features a 280 mm stroke (approaching the 300 mm threshold), the unsupported rod length increases the risk of side-load bending at the rod bearing; for heavy off-center loads, integrate an external guide rail to prevent premature wear.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The SE50X280S generates 982 N of push force and 825 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 1374 N. The maximum allowable push force is 200 kgf when operating at the maximum pressure of 1.0 MPa.
Yes, the SE50X280S is dimensionally interchangeable per ISO 15552 standards. You can drop it in as a replacement for other ISO 15552 profile cylinders, provided your mounting hardware, PT1/4 ports, and M16x1.5 rod-end thread match the standardized interface.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.