
The AirTAC SE50 Standard Cylinder SE50X50SFA is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 50mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X50SFA is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver a 982 N push force at 0.5 MPa. Fitted with a front flange (FA) mounting accessory, it provides rigid frontal support for high-inertia loads. The square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This 50 mm bore unit includes a built-in magnet (-S) for seamless integration with AirTAC CMSE reed and DMSE electronic sensors. The field-adjustable air cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration via a set screw, effectively softening hard mechanical stops without relying on fixed rubber bumpers.
| Model | Airtac SE50 Standard Cylinder SE50X50SFA |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 982 N push force required to fold and seal corrugated carton blanks on high-speed packaging lines, utilizing the 50 mm stroke for rapid cycling.
Drives small bronze bushings into automotive gearbox housings, where the FA front flange absorbs the 0.7 MPa 1374 N thrust without deflection.
Actuates routing gates on modular conveyor networks, using the integrated magnet to trigger DMSE solid-state sensors for precise position feedback.
When sizing this actuator, compare its 982 N push force against your actual load requirements. Stepping down to a 40 mm bore reduces the 0.5 MPa push capacity to 628 N, whereas stepping up to a 63 mm bore increases it to 1559 N. Keep in mind that a standard SE cylinder cannot hold a load if air pressure drops; if your application requires static position holding during exhaust or valve centering, you must integrate an external pilot-operated check valve or transition to a BSE rod-lock variant.
Because this model carries an FA front flange, it is well-suited for heavy inline thrust applications. The 50 mm bore features a 20 mm rod and a PT1/4 port. As a dimensionally interchangeable ISO 15552 component, it serves as a direct replacement for other ISO 15552 cylinders, sharing standard mounting hardware and centerline dimensions.
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N. The maximum operating pressure is 1.0 MPa, yielding a maximum push force of 200 kgf.
Yes. The SE50X50SFA is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint, pilot port spacing, and rod-end thread (M16x1.5) as other standard ISO 15552 profile cylinders, allowing for a direct retrofit.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.