
The AirTAC SE50 Standard Cylinder SE50X5S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 5mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X5S is a double-acting single-rod ISO 15552 profile cylinder engineered for ultra-short 5 mm strokes, delivering 982 N of push force at 0.5 MPa and 1374 N at 0.7 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush within tight machine envelopes. The integrated -S magnet enables direct fitment of CMSE reed and DMSE electronic sensors along the triple-sided sensor grooves for precise end-of-travel signaling.
Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration via a set screw, protecting the mechanism during high-speed 30-800 mm/s cycling. Because this is a standard ISO 15552 footprint, it serves as a direct replacement for any cylinder sharing the VDMA 24562 mounting interface, streamlining retrofits without altering existing fixture dimensions.
| Model | Airtac SE50 Standard Cylinder SE50X5S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 5 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 5 mm stroke to deliver a rapid 982 N push at 0.5 MPa for knocking small stamped metal parts out of a die on every machine cycle.
Employs the ultra-short stroke and built-in DMSE electronic sensor magnet to tuck packaging flaps at high speed before tape application.
Leverages the compact, tie-rod-free extruded profile to securely hold delicate circuit boards in an inspection jig without over-traveling.
Selecting the SE50X5S is ideal when a brief 5 mm extension is required with moderate thrust. If you need less power, step down to the 40 mm bore, which provides 628 N of push at 0.5 MPa. If your fixture demands more force, step up to the 63 mm bore, yielding 1559 N of push at 0.5 MPa. This 50 mm bore utilizes a PT1/4 port and an M16x1.5 rod thread, matching the standard ISO 15552 mounting dimensions and sharing hardware with similar profile cylinders.
Keep in mind that a plain SE cylinder does not hold a load when air pressure is lost or the valve is centered; the piston will drift. If your 5 mm stroke application requires strict position holding without live pressure, consider the BSE rod-lock variant or an external pilot-operated check valve. Furthermore, because the stroke is only 5 mm, side-load stress on the rod bearing is minimal compared to longer strokes, though external guides remain best practice for offset loads.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The SE50X5S provides a push force of 982 N and a pull force of 825 N at 0.5 MPa. At 0.7 MPa, the push force is 1374 N, with a maximum push of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50X5S is dimensionally interchangeable per ISO 15552 (VDMA 24562) standards. It shares the same mounting interface and PT1/4 porting as other profile cylinders, allowing a direct retrofit. The built-in -S magnet is specifically designed for AirTAC CMSE and DMSE sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.