Airtac SE50 Standard Cylinder SE50X60
The AirTAC Airtac SE50 Standard Cylinder SE50X60 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 60mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ50 mm
- Stroke60 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
About the Airtac SE50 Standard Cylinder SE50X60
The AirTAC SE50X60 is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver a 982 N push at 0.5 MPa over a 60 mm stroke. Its extruded aluminum square barrel omits external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly in tight machinery spaces.
This unit relies on a field-adjustable pneumatic cushion at both ends to decelerate the piston near stroke limits, allowing you to tune out hard end-stop impacts at speed. As this specific SKU lacks the -S magnet option, it does not support direct CMSE or DMSE position sensing without modification.
Airtac SE50 Standard Cylinder SE50X60 Technical Specifications
| Model | Airtac SE50 Standard Cylinder SE50X60 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE50 Standard Cylinder SE50X60
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE50 Standard Cylinder SE50X60 Is Used
Carton Flap Folding
Provides the precise 982 N push and 60 mm travel needed to tuck corrugated carton flaps during high-speed case erecting.
Bottle Diverting Gate
Actuates a short-stroke routing gate on a packaging line, using its adjustable cushion to softly arrest the 60 mm extension without jarring the glass containers.
Component Press Fit
Drives a small bushing into an aluminum housing on an assembly press, utilizing the 825 N retract force to cleanly pull back the tooling.
Is the Airtac SE50 Standard Cylinder SE50X60 the Right Cylinder?
When sizing this 50 mm bore, compare its 982 N push at 0.5 MPa against the 40 mm bore (628 N) if your load is lighter, or step up to the 63 mm bore (1559 N) for heavier demands. Because this is a standard double-acting cylinder, it will drift if air pressure is lost or the valve centers; use a BSE rod lock for strict position holding.
As a true ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for any standard 50 mm bore cylinder with a PT1/4 port and 60 mm stroke, sharing standard mounting accessories like FA or LB brackets.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE50 Standard Cylinder SE50X60 FAQ
The SE50X60 delivers a push force of 982 N and a pull force of 825 N at 0.5 MPa. At 0.7 MPa, the push force is 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50X60 is dimensionally interchangeable per ISO 15552. You can use it as a drop-in replacement for other 50 mm bore ISO 15552 profile cylinders, retaining your existing PT1/4 port plumbing and mounting brackets.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE50 Standard Cylinder SE50X60
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.