Airtac SE63 Standard Cylinder SE63AX10S
The AirTAC SE63 Standard Cylinder SE63AX10S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 10mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ63 mm
- Stroke10 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE63 Standard Cylinder SE63AX10S
The AirTAC SE63AX10S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 1559 N push at 0.5 MPa. It features a 63 mm bore and a 10 mm stroke, making it ideal for short, high-impact motions. The extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
This specific configuration includes a SUS420J2 stainless steel rod (code A) for superior resistance in washdown or mildly corrosive environments. Equipped with a built-in magnet (code S), it supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushions at both ends allow you to tune deceleration, protecting the mechanism during rapid cycling.
Airtac SE63 Standard Cylinder SE63AX10S Technical Specifications
| Model | Airtac SE63 Standard Cylinder SE63AX10S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE63 Standard Cylinder SE63AX10S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE63 Standard Cylinder SE63AX10S Is Used
Stamping Press Ejection
Uses the 1559 N push force to eject formed metal blanks from a stamping die in just 10 mm of travel.
Carton Sealing Flap Fold
Rapidly folds corrugated carton flaps prior to tape application, leveraging the short 10 mm stroke for high-speed cycling.
Lab Dispenser Clamping
Secures small fluid dispenser bottles during filling, utilizing the SUS420J2 stainless rod to resist chemical spills.
Is the Airtac SE63 Standard Cylinder SE63AX10S the Right Cylinder?
Selecting this 63 mm bore provides 1559 N push and 1402 N pull at 0.5 MPa. If your application requires less force, stepping down to the 50 mm bore yields 982 N push, while stepping up to the 80 mm bore provides 2513 N push for heavier loads. This model uses a PT3/8 port and includes the -S magnet for position sensing. To retrofit an existing setup, match the 63 mm bore, 10 mm stroke, PT3/8 port, and your required mounting accessory, as the ISO 15552 dimensions ensure direct compatibility. Remember that the adjustable cushion only decelerates the piston near stroke end; it does not hold the load if air pressure is lost, so consider a BSE rod lock for strict position holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE63 Standard Cylinder SE63AX10S FAQ
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N push and 1402 N pull. At 0.7 MPa, the push increases to 2182 N, with a maximum push of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE63AX10S is dimensionally interchangeable per ISO 15552, allowing it to serve as a direct replacement for other standard profile cylinders. It uses a PT3/8 port and features a SUS420J2 stainless steel rod for washdown duty.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE63 Standard Cylinder SE63AX10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.