
The AirTAC SE63 Standard Cylinder SE63AX145 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 145mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63AX145 is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding environments. Equipped with a SUS420J2 stainless steel rod (code A), it is purpose-built for corrosive or washdown duty. Operating at 0.5 MPa, it generates a push force of 1559 N and a pull force of 1402 N, extending across a 145 mm stroke.
The extruded aluminum barrel omits external tie rods, yielding a compact, flush-mounting footprint that resists corrosion and simplifies sensor placement along its three integrated grooves. Because this specific SKU lacks the -S magnet option, it does not support AirTAC CMSE or DMSE position sensors out of the box. Field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration to soften hard impacts.
| Model | Airtac SE63 Standard Cylinder SE63AX145 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 145 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×145 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 1559 N of push at 0.5 MPa to drive the end-seal jaw assembly on a flow wrapper, with the SUS420J2 rod tolerating daily washdowns.
Delivers precise 145 mm travel to lock and unlock a high-speed centrifuge access door, leveraging the corrosion-resistant stainless steel rod.
Actuates a routing flap to sort filled containers on a bottling line, relying on the field-adjustable cushioning to prevent fluid-sloshing sudden stops.
If 1559 N of push at 0.5 MPa is too much for your payload, step down to the 50 mm bore, which yields 982 N. If your application requires more thrust, step up to the 80 mm bore, providing 2513 N. Keep in mind that a standard SE cylinder will drift and drop its load if air pressure is lost or the valve is centered; for position holding, you need a BSE rod lock variant or an external pilot-operated check valve. With a 145 mm stroke, side loading is minimal, but the Ø20 mm rod and M16x1.5 thread handle standard bending stresses well.
Quick checklist
The SE63AX145 generates a push force of 1559 N and a pull force of 1402 N at 0.5 MPa. At 0.7 MPa, the push force is 2182 N, with a maximum push of 318 kgf at 1.0 MPa. It uses a PT3/8 port and operates at speeds of 30-800 mm/s.
Yes, the SE63AX145 is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting footprint and hardware dimensions of other ISO 15552 profile cylinders. Note that because this SKU lacks the -S magnet, it cannot host AirTAC CMSE or DMSE sensors without modification.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.