
The AirTAC SE63 Standard Cylinder SE63AX220 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 220mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63AX220 is a double-acting, single-rod ISO 15552 profile cylinder featuring a 63 mm bore and 220 mm stroke. It generates 1559 N of push force and 1402 N of pull force at 0.5 MPa, making it well-suited for medium-duty industrial actuation. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This specific SKU utilizes a SUS420J2 stainless steel piston rod (code A) to resist corrosion in washdown or mildly acidic environments. Pneumatic cushioning at both ends is field-adjustable via a setscrew, allowing you to tune end-of-stroke deceleration and eliminate hard metal impacts. Note that this unit ships without a position magnet, so CMSE or DMSE electronic sensors will not function on this variant without modification.
| Model | Airtac SE63 Standard Cylinder SE63AX220 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 220 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×220 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the pulling mechanism on vertical packaging lines, using its 1559 N push force and 220 mm stroke to reliably feed film rolls in damp production areas.
Actuates routing gates on washdown-grade bottle conveyors, where the SUS420J2 stainless rod withstands daily exposure to cleaning chemicals and water spray.
Precisely strokes a pneumatic knife to shear paper sheets, relying on the adjustable end cushions to soften the 220 mm travel impact at high cycling speeds.
If your application requires less force, stepping down to a 50 mm bore reduces the 0.5 MPa push to 982 N. Conversely, upgrading to an 80 mm bore increases the 0.5 MPa push to 2513 N. Because this is a 220 mm stroke unit, the unsupported rod length extends significantly during operation; you should incorporate an external guide to prevent side-load bending and rod-bearing wear.
As a true ISO 15552 cylinder, the SE63AX220 is dimensionally interchangeable with other ISO 15552 profile cylinders, simplifying retrofits. Remember that the adjustable air cushion only decelerates the piston near stroke end and does not hold a load if air pressure is lost. For position holding, consider a BSE rod lock variant.
Quick checklist
The SE63AX220 delivers 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum push of 318 kgf at 1.0 MPa. It uses a PT3/8 air port.
No, this specific SKU does not include a built-in magnet. To use AirTAC CMSE reed or DMSE electronic sensors, you would need a variant with the -S magnet option.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.