Airtac SE63 Standard Cylinder SE63AX275S
The AirTAC SE63 Standard Cylinder SE63AX275S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 275mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ63 mm
- Stroke275 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE63 Standard Cylinder SE63AX275S
The AirTAC SE63AX275S is a double-acting single-rod profile cylinder built to the ISO 15552 / VDMA 24562 standard. It delivers a robust 1559 N push force at 0.5 MPa and features a 275 mm stroke. Engineered with a square extruded aluminum barrel, it entirely eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This specific configuration includes a SUS420J2 stainless steel rod (code A) for superior resistance in corrosive or washdown environments, and a built-in magnet (code S) for position sensing. The barrel features sensor grooves on three sides, allowing you to easily drop in CMSE reed or DMSE electronic switches wherever the mounting layout dictates, without needing extra brackets.
Airtac SE63 Standard Cylinder SE63AX275S Technical Specifications
| Model | Airtac SE63 Standard Cylinder SE63AX275S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 275 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE63 Standard Cylinder SE63AX275S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×275 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE63 Standard Cylinder SE63AX275S Is Used
Palletizer Pusher
Provides 1559 N of push at 0.5 MPa to positively index shrink-wrapped pallets through a stretch wrapper, with the SUS420J2 rod enduring humid packing environments.
Bottle Diverter Gate
Utilizes the 275 mm stroke and built-in magnet to actuate a routing flap on a high-speed filling line, triggering DMSE electronic sensors for precise position confirmation.
Lab Washdown Station
Deploys the SUS420J2 stainless rod to extend cleaning nozzles into glassware rinsing zones, resisting water spray while cycling at speeds up to 800 mm/s.
Is the Airtac SE63 Standard Cylinder SE63AX275S the Right Cylinder?
If your application requires less thrust, stepping down to the 50 mm bore yields 982 N of push force at 0.5 MPa, whereas stepping up to the 80 mm bore provides 2513 N. Because this is a 275 mm stroke, the unsupported piston rod is subjected to greater bending moments under side loads; for heavy offset loads, utilize an external guide rail to prevent premature rod-bearing wear. Remember that a standard SE cylinder does not hold its position when air pressure is lost or exhausted—the piston will drift. For fail-safe load holding, integrate an external pilot-operated check valve or select the BSE rod-lock variant. As a true ISO 15552 cylinder, it serves as a direct dimensional replacement for other ISO 15552 profile cylinders, sharing identical mounting hardware and port sizes (PT3/8).
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE63 Standard Cylinder SE63AX275S FAQ
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push (extend) force and 1402 N of pull (retract) force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push rating of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE63AX275S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint, port size (PT3/8), and rod thread (M16x1.5) as other ISO 15552 profile cylinders. It also features field-adjustable air cushioning at both ends to fine-tune end-of-stroke deceleration.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE63 Standard Cylinder SE63AX275S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.