Airtac SE63 Standard Cylinder SE63AX290S
The AirTAC SE63 Standard Cylinder SE63AX290S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 290mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ63 mm
- Stroke290 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE63 Standard Cylinder SE63AX290S
The AirTAC SE63AX290S is a double-acting single-rod ISO 15552 profile cylinder engineered for a 63 mm bore and a 290 mm stroke. It generates a push force of 1559 N and a pull force of 1402 N at 0.5 MPa, peaking at a maximum push of 318 kgf at 1.0 MPa. Equipped with a SUS420J2 stainless steel rod, it is specifically built for corrosive or washdown environments where a standard carbon steel piston rod would fail prematurely.
The extruded aluminum barrel lacks external tie rods, yielding a compact, smooth profile that mounts flush against machine frames while resisting debris buildup. Field-adjustable air cushioning at both ends allows you to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 30-800 mm/s. The integrated -S magnet supports AirTAC CMSE reed and DMSE electronic sensors for precise position feedback along the PT3/8 ported body.
Airtac SE63 Standard Cylinder SE63AX290S Technical Specifications
| Model | Airtac SE63 Standard Cylinder SE63AX290S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 290 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE63 Standard Cylinder SE63AX290S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×290 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE63 Standard Cylinder SE63AX290S Is Used
Flow Wrapper End-Seal Head
Drives the rotating sealing jaw on a continuous flow wrapper, utilizing the 1559 N push force to cleanly cut and seal packaging film at high cycle rates.
Pilot Plant Reactor Lid
Lifts and lowers a 20-liter stainless steel reactor vessel lid, relying on the SUS420J2 rod to withstand chemical washdowns and the 290 mm stroke for full clearance.
Beverage Bottle Sorting Gate
Actuates a diverter gate on a bottle sorting conveyor, where the smooth tie-rod-free profile prevents glass dust accumulation and the DMSE sensor confirms gate position.
Is the Airtac SE63 Standard Cylinder SE63AX290S the Right Cylinder?
When sizing this 63 mm bore actuator, evaluate your force margins: stepping down to a 50 mm bore reduces the 0.5 MPa push to 982 N, while stepping up to an 80 mm bore increases it to 2513 N. Because this is a double-acting cylinder, it will drift if air pressure is lost or the valve is centered; it cannot hold a load safely without live pressure, so add a BSE rod lock for fail-safe holding. The 290 mm stroke on a Ø20 mm rod warrants an external guide to prevent rod-bearing bending under heavy side loads. As a true ISO 15552 cylinder, it serves as a dimensionally interchangeable direct replacement for other ISO 15552 profile cylinders, sharing standard mounting hardware.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE63 Standard Cylinder SE63AX290S FAQ
The SE63AX290S provides a push force of 1559 N and a pull force of 1402 N at 0.5 MPa, a push of 2182 N at 0.7 MPa, and a maximum push of 318 kgf at 1.0 MPa. It features a PT3/8 port and an M16x1.5 rod-end thread.
Yes, it is dimensionally interchangeable per ISO 15552, acting as a direct replacement for other ISO 15552 profile cylinders. However, the adjustable air cushion only decelerates the piston near stroke end; it is not a brake, so the cylinder will drift if air is lost. Use a BSE rod lock for position holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE63 Standard Cylinder SE63AX290S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.