
The AirTAC SE63 Standard Cylinder SE63AX30 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 30mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63AX30 is a double-acting single-rod ISO 15552 profile cylinder engineered for short-stroke actuation in demanding environments. It delivers a robust 1559 N push at 0.5 MPa, utilizing a 63 mm bore and a 30 mm stroke. This specific SKU features an SUS420J2 stainless steel piston rod, making it highly suitable for corrosive or washdown applications where standard carbon steel would fail.
The extruded aluminum barrel design omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting contamination. Field-adjustable air cushioning at both end caps allows technicians to tune the deceleration of the piston, effectively softening hard end stops during high-speed operations. Note that this configuration ships without a sensor magnet, so position detection is not supported out of the box.
| Model | Airtac SE63 Standard Cylinder SE63AX30 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives capping heads in beverage lines where the SUS420J2 rod withstands daily chemical washdowns, applying precise 1559 N downward force to seal containers.
Executes rapid 30 mm strokes to position cardboard blanks in packaging machinery, relying on adjustable cushions to absorb rapid cycling impacts.
Pivots stainless steel diverter gates on food-grade conveyors, utilizing the tie-rod-free profile to prevent bacterial traps in hygiene-critical zones.
Selecting this 63 mm bore cylinder makes sense when your application requires approximately 1559 N of push force at 0.5 MPa. If your load is lighter, stepping down to the 50 mm bore yields 982 N of push, whereas heavier loads might require the 80 mm bore, which provides 2513 N. This model uses a PT3/8 port and an M16x1.5 rod thread, carrying a 20 mm rod that handles side loads well even at the short 30 mm stroke.
As a standard ISO 15552 profile cylinder, it serves as a direct dimensional replacement for other ISO 15552 cylinders, simplifying retrofits. Remember that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking device. If your process demands fail-safe load holding without live air pressure, consider the BSE rod-lock variant or an external pilot-operated check valve.
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push and 1402 N of pull. At 0.7 MPa, the push force is 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. It operates within a pressure range of 0.15-1.0 MPa and supports speeds from 30-800 mm/s.
This specific SKU lacks the built-in magnet required for CMSE or DMSE position sensors. Dimensionally, it is an ISO 15552 profile cylinder, meaning it serves as a direct replacement for any standard ISO 15552 mounting interface without requiring custom brackets.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.