verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63AX475

The AirTAC SE63 Standard Cylinder SE63AX475 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 475mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke475 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$192.12 $199.62Save 3% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE63 Standard Cylinder SE63AX475

The AirTAC SE63AX475 is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver a robust 1559 N push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while integrating standardized ISO 15552 interface dimensions for seamless retrofitting.

This specific SKU is configured with a SUS420J2 stainless steel rod (option A) to resist corrosion in washdown or mildly acidic environments. The 475 mm stroke is covered under standard capabilities, and field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-of-stroke deceleration via a set screw, softening hard impacts during high-speed 30-800 mm/s cycling. Note that this unit lacks a built-in magnet, so it does not support CMSE or DMSE position sensors without modification.

Airtac SE63 Standard Cylinder SE63AX475 Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63AX475
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke475 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63AX475

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×475Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63AX475 Is Used

conveyor_belt

Bottling Line Diverters

Actuates routing gates on stainless beverage lines, using the 1559 N push force to pivot heavy guide arms while the SUS420J2 rod resists daily chemical washdowns.

packaging

Case Erector Jaws

Drives the folding mechanism on continuous-motion carton erectors, where the 475 mm stroke provides the reach needed to clear wide packaging formats.

science

Lab Sample Dispensing

Moves fluid dispensing heads across analytical stations, benefiting from the smooth pneumatic cushioning to prevent liquid splash during 30-800 mm/s travel.

Is the Airtac SE63 Standard Cylinder SE63AX475 the Right Cylinder?

When sizing this actuator, compare its 1559 N push at 0.5 MPa against the neighboring bores: step down to a 50 mm bore for 982 N if your load is lighter, or step up to an 80 mm bore for 2513 N if you need higher thrust margin. Because this 475 mm stroke creates a long unsupported rod extension, side loads will induce bending moments on the rod bearing, so an external guide rail is strongly recommended to prevent premature seal wear. As a standard ISO 15552 cylinder, it serves as a dimensionally interchangeable direct replacement for other ISO 15552 cylinders, matching the 63 mm bore, 475 mm stroke, PT3/8 port, and standard mounting accessories. Remember that the double-acting air cushion only decelerates the piston near stroke end; it does not hold the load if air pressure is lost, so a BSE rod lock is required for fail-safe positioning.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63AX475 FAQ

At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.

Yes. The SE63AX475 is dimensionally interchangeable with other ISO 15552 profile cylinders, utilizing the same mounting interface and PT3/8 port. However, because this specific SKU lacks the -S magnet option, it will not trigger CMSE or DMSE electronic sensors without adding a magnet.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63AX475

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE63AX475 and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.