
The AirTAC SE63 Standard Cylinder SE63AX475S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 475mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63AX475S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 1559 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion. The SUS420J2 stainless steel piston rod equips this unit for washdown and mildly corrosive environments where standard carbon steel would fail.
A built-in magnetic piston enables position detection with AirTAC CMSE reed or DMSE electronic sensors, dropped directly into the sensor grooves machined on three sides of the body. Field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune the end-of-stroke deceleration via a set screw, smoothly slowing the 475 mm travel without jarring impacts.
| Model | Airtac SE63 Standard Cylinder SE63AX475S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 475 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×475 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1559 N push force and 475 mm stroke to deflect plastic bottles between packaging lanes, with the SUS420J2 rod enduring daily washdowns.
Extends the full 475 mm to position stretch film rolls, relying on the adjustable end cushions to soften stops at high cycle speeds.
Shifts an auxiliary machining head along a 475 mm axis, tracking position via DMSE electronic sensors in the integrated barrel grooves.
This 63 mm bore generates 1559 N of push at 0.5 MPa. If your application requires less force, stepping down to the 50 mm bore yields 982 N of push, while stepping up to the 80 mm bore provides 2513 N to handle heavier payloads. Because this is a 475 mm stroke, the extended rod is subject to bending under side loads; always support the load with an external guide to prevent premature rod-bearing wear.
As a true ISO 15552 profile cylinder, the SE63AX475S serves as a direct dimensional replacement for any standard ISO 15552 cylinder, matching the 63 mm bore, 475 mm stroke, PT3/8 port, and standardized mounting accessories. Note that the adjustable air cushion only decelerates the piston near stroke end—it does not lock or hold the load. If air pressure is lost, the rod will drift; use a BSE rod lock for fail-safe position holding.
Quick checklist
At 0.5 MPa it provides 1559 N push and 1402 N pull. At 0.7 MPa the push increases to 2182 N, with a maximum push of 318 kgf at 1.0 MPa. The operating speed ranges from 30-800 mm/s.
Yes, the SE63AX475S is dimensionally interchangeable per ISO 15552. You can drop it in using the same 63 mm bore, 475 mm stroke, PT3/8 ports, and standard mounting hardware without modifying the machine frame.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.