verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X135

The AirTAC SE63 Standard Cylinder SE63X135 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 135mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke135 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$91.41 $98.91Save 7% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X135

The AirTAC SE63X135 is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 1559 N of push force and 1402 N of pull force at 0.5 MPa. It operates reliably within a 0.15-1.0 MPa pressure range and features a PT3/8 port paired with a 20 mm hard-chrome plated rod. Because it lacks external tie rods, its square extruded aluminum barrel provides a flush, corrosion-resistant housing that simplifies mounting and maximizes spatial efficiency in tight machine cells.

This specific SKU is configured without a built-in magnet, meaning it is not equipped for AirTAC CMSE or DMSE electronic position sensing out of the box. To manage dynamic loads, the cylinder incorporates field-adjustable air cushioning at both ends, allowing technicians to tune the end-of-stroke deceleration via a set screw rather than relying on a fixed rubber bumper. It achieves a standard travel length of 135 mm while maintaining a broad speed range of 30-800 mm/s.

Airtac SE63 Standard Cylinder SE63X135 Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X135
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke135 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X135

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×135Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X135 Is Used

precision_manufacturing

CNC Lathe Bar Feeder

Pushes raw bar stock through the lathe spindle with 1559 N of force at 0.5 MPa, using the 135 mm stroke to index material precisely during automated turning cycles.

packaging

Case Erector Flap Folder

Folds corrugated carton flaps at high speed, relying on the field-adjustable air cushion to soften the end stop and prevent tearing the packaging board.

factory

Injection Mold Platen Ejector

Ejects molded plastic parts from the machine platen, where the square no-tie-rod profile allows the cylinder to mount flush against the press frame in tight tooling spaces.

Is the Airtac SE63 Standard Cylinder SE63X135 the Right Cylinder?

When sizing this 63 mm bore actuator, consider stepping down to the 50 mm bore if your application only requires 982 N of push force at 0.5 MPa, or moving up to the 80 mm bore for a substantial 2513 N push to handle heavier payloads. As a standard ISO 15552 profile cylinder, this unit serves as a direct dimensional replacement for other ISO 15552 cylinders, sharing the exact same mounting interface and accessory footprint. To match this exact SKU on a retrofit, specify a 63 mm bore, 135 mm stroke, PT3/8 port, basic mounting, and no sensor magnet. Note that a plain SE cylinder does not hold its position or load when air is lost or the valve is centered; the piston will drift, so if your process demands mid-stroke holding without live pressure, explore the BSE rod lock variant. Additionally, while the 20 mm rod and M16x1.5 thread handle moderate side loading well, any stroke of 300 mm or more requires an external guide to prevent rod-bearing bending and premature seal wear.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X135 FAQ

At 0.5 MPa, the SE63X135 provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.

Yes, the SE63X135 is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint and dimensions as other standard ISO 15552 profile cylinders. It uses a PT3/8 port and a 20 mm rod, making it a direct retrofit for existing machinery.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X135

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X135 and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.