
The AirTAC SE63 Standard Cylinder SE63X15 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 15mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X15 is a double-acting, single-rod ISO 15552 profile cylinder engineered for short-stroke actuation. It delivers a robust 1559 N push force at 0.5 MPa alongside a 1402 N pull force, making it ideal for high-impact clamping and ejection tasks within a 15 mm travel. Its square extruded aluminum barrel completely eliminates external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly to machine frames.
This specific SKU omits the built-in magnet, meaning it operates without electronic position feedback out of the box. To manage rapid kinetic energy across its 36 mm cushion length, the cylinder features field-adjustable pneumatic cushioning at both ends. By turning a simple screw, technicians can tune the end-of-stroke deceleration to soften hard mechanical stops, preventing premature wear on the M16x1.5 rod thread during rapid 30-800 mm/s cycles.
| Model | Airtac SE63 Standard Cylinder SE63X15 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1559 N push force to knock finished plastic parts from injection molds, where the short 15 mm stroke delivers rapid, localized impact.
Secures copper stator assemblies during electric motor winding, relying on the extruded profile barrel for flush mounting against tight machine guards.
Drives short mechanical folders to tuck packaging flaps on high-speed lines, tuning the adjustable end cushions to absorb abrupt stops.
Choosing this 63 mm bore provides 1559 N of thrust at 0.5 MPa. If your assembly requires less force, stepping down to the 50 mm bore yields 982 N of push, while moving up to the 80 mm bore provides 2513 N for heavier fixtures. Because this unit lacks a magnet (-S), it cannot host CMSE or DMSE sensors; if your control system requires position signaling, select the SE63X15S variant instead. As a true ISO 15552 cylinder, it is dimensionally interchangeable with other ISO 15552 cylinders, allowing you to reuse existing PT3/8 port plumbing and standardized mounting brackets effortlessly.
Keep in mind that a plain SE cylinder does not hold its load when air pressure is lost or the valve is centered—the piston will drift. If your 15 mm stroke application demands absolute position holding without live pressure, you must integrate an external pilot-operated check valve or pivot to the BSE rod-lock series. Furthermore, while the 20 mm rod handles standard loads well, any application shifting heavy offset masses should employ an external guide to prevent rod-bearing bending.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force reaches 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. It operates at speeds between 30-800 mm/s.
Yes. The SE63X15 is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint, PT3/8 port size, and M16x1.5 rod thread as other ISO 15552 profile cylinders, making it a direct retrofit.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.