
The AirTAC SE63 Standard Cylinder SE63X230 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 230mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X230 is a double-acting, single-rod ISO 15552 profile cylinder delivering a robust 1559 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized sensor grooves on three sides.
This 63 mm bore unit features a 20 mm hard-chrome piston rod and a 36 mm field-adjustable pneumatic cushion at both ends. The cushioning screws let technicians dial in end-of-stroke deceleration to soften hard impacts at speed, functioning as a true velocity brake rather than a fixed rubber bumper.
| Model | Airtac SE63 Standard Cylinder SE63X230 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 230 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×230 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 1559 N push at 0.5 MPa required to fold and seal corrugated carton blanks reliably during high-speed packaging line cycles.
Uses the 230 mm stroke to push heavy pallets sideways onto branching conveyor tracks, benefiting from the flush no-tie-rod profile to avoid snagging.
Drives small bushings into automotive gearbox housings, utilizing the adjustable end cushions to prevent component damage during rapid retraction.
Stepping down to the 50 mm bore yields 982 N of push at 0.5 MPa, whereas moving up to the 80 mm bore provides 2513 N, letting you scale power precisely for the 230 mm stroke. Because this SKU lacks the -S magnet, it cannot host CMSE or DMSE position sensors; if your sequence control requires end-of-stroke feedback, specify an SE63X230S variant. Since the 230 mm stroke exceeds 300 mm, long unsupported piston rods are susceptible to bending under side loads, so utilize an external guide to prevent rod-bearing wear. Note that a plain SE cylinder will drift if air pressure is lost; use a BSE rod lock for fail-safe holding. Being dimensionally interchangeable per ISO 15552, it serves as a direct replacement for other profile cylinders sharing the VDMA 24562 mounting interface.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
The SE63X230 generates a push force of 1559 N and a pull force of 1402 N at 0.5 MPa. At 0.7 MPa, the push force is 2182 N, and the maximum push force is 318 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable per ISO 15552 and VDMA 24562 standards, allowing it to drop into existing mounting hardware without frame modifications. It uses a PT3/8 port and features a field-adjustable air cushion at both ends.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.