
The AirTAC SE63 Standard Cylinder SE63X250CB is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 250mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X250CB is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 1559 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact body that resists corrosion and mounts flush against machine frames. The CB double clevis mounting accessory equips this unit for pivoting articulations where the actuator must swing through an arc.
This 63 mm bore unit features a PT3/8 port, a 20 mm hard-chrome rod, and field-adjustable pneumatic cushioning at both ends to soften end-of-stroke impacts. Note that this specific SKU lacks a built-in magnet, so it does not support CMSE or DMSE electronic position sensing without modification. The cushioning is a deceleration feature only, not a locking mechanism.
| Model | Airtac SE63 Standard Cylinder SE63X250CB |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 250 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the CB double clevis to articulate a heavy conveyor belt tensioning arm, delivering 1559 N push to maintain optimal tracking dynamics under varying loads.
Swings a metal blank into a stamping press using the 250 mm stroke, relying on the adjustable end cushions to absorb the kinetic energy of the 318 kgf maximum thrust.
Pivots corrugated case flaps during high-speed carton erecting, where the double-acting 63 mm bore provides the consistent 1402 N retract force needed for crisp folds.
Selecting this 63 mm bore makes sense when your application requires the 1559 N push at 0.5 MPa that this model provides. If you need less force, the 50 mm bore steps down to 982 N push, while stepping up to the 80 mm bore yields 2513 N push. Because this SKU lacks the -S magnet, you cannot track piston position with reed switches; if your pivot mechanism requires end-of-stroke feedback, specify the -S option. The CB double clevis is ideal for articulating loads, but ensure the clevis pin is greased to handle the side loads generated during the swing.
With a 250 mm stroke, the 20 mm rod and its bearing experience increased bending moments under heavy lateral loads. Even with the robust M16x1.5 rod thread, an external guide rail should be used to prevent premature seal wear if the load is not perfectly axial. The unit is dimensionally interchangeable with other ISO 15552 profile cylinders, allowing you to drop it into existing footprints without altering the mounting interface.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
This 63 mm bore cylinder features a PT3/8 port and generates 1559 N push and 1402 N pull at 0.5 MPa. At 0.7 MPa, the push force is 2182 N. The maximum thrust is 318 kgf at the 1.0 MPa operating pressure limit.
No, the adjustable air cushion at both ends only decelerates the piston near the stroke limits; it is not a braking device. If your pivoting CB mount application must hold a load without live air pressure, you need a separate rod lock like the BSE series or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.