
The AirTAC SE63 Standard Cylinder SE63X260 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 260mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X260 is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver a 1559 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
This 63 mm bore unit features a 260 mm stroke and a PT3/8 port. Field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed cycling. Note that this specific SKU lacks a built-in magnet, so it does not support CMSE or DMSE electronic position sensing without modification.
| Model | Airtac SE63 Standard Cylinder SE63X260 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 260 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×260 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a routing flap on a packaging conveyor, utilizing the 1559 N push force to reliably swing heavy loaded pallets onto auxiliary tracks.
Drives the mechanical folder arms on a case erector, using the 260 mm stroke to fully extend and tuck major flaps before tape application.
Secures raw aluminum castings inside a machining center, applying consistent 0.5 MPa clamping pressure without obstructing the cutting zone.
When sizing this 63 mm bore actuator, compare its 1559 N push at 0.5 MPa against your actual load requirements. If you need less force, stepping down to the 50 mm bore yields 982 N of push, while stepping up to the 80 mm bore provides 2513 N for heavier payloads. Because the 260 mm stroke creates a long lever arm on the 20 mm rod, external guiding is recommended to prevent rod-bearing bending under lateral loads.
As a true ISO 15552 profile cylinder, the SE63X260 serves as a direct replacement for any standard 63 mm bore, 260 mm stroke unit, sharing identical mounting interface dimensions for foot, flange, or trunnion hardware. Remember that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking mechanism, so loads will drift if air pressure is lost.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable with any ISO 15552 63 mm bore cylinder, matching standard mounting and PT3/8 port locations. However, this specific SKU does not have a built-in magnet, so it cannot support CMSE or DMSE position sensors without ordering the -S magnet variant.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.