
The AirTAC SE63 Standard Cylinder SE63X300FTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 300mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X300FTC is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver a robust 1559 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. This clean profile design prevents debris buildup while streamlining mechanical integration.
Equipped with an FTC mounting accessory, this 63 mm bore unit utilizes a PT3/8 port and a Ø20 mm rod with an M16x1.5 thread. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, effectively softening hard mechanical stops at high cycling speeds. Note that this specific SKU lacks a built-in magnet, meaning it is not wired for AirTAC CMSE or DMSE position sensing without modification.
| Model | Airtac SE63 Standard Cylinder SE63X300FTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 300 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1559 N push force and 300 mm stroke to index filled corrugated cases onto a palletizing layer, with the FTC mount absorbing high lateral transfer loads.
Positions steel sheet metal backstops precisely in a CNC press brake, relying on the adjustable end cushions to prevent bounce when cycling at high speeds.
Drives an automated parts ejector arm on a 200-ton injection molding machine, benefiting from the flush tie-rod-free barrel that resists resin dust accumulation.
Delivering 1559 N of thrust at 0.5 MPa, this bore sits perfectly between the 50 mm option (982 N push) and the 80 mm option (2513 N push), allowing you to scale up or down depending on your exact payload requirements. Because the stroke is 300 mm, the unsupported rod length increases bending moments under lateral stress; utilizing an external guide rail is highly recommended to prevent premature rod-bearing wear. Remember that the adjustable air cushion only decelerates the piston near the end of its travel—it does not lock or hold the load. If your fixture must maintain vertical position during a complete air loss, you must integrate a BSE rod lock or an external pilot-operated check valve. As a dimensionally interchangeable ISO 15552 component, it serves as a direct replacement for other standard profile cylinders, sharing identical mounting footprints and hardware.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
This 63 mm bore cylinder generates 1559 N of push force and 1402 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 2182 N, with an absolute maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable with any standard ISO 15552 profile cylinder, allowing you to reuse existing FTC mounting hardware and footprints. However, it is a standard double-acting cylinder and does not hold its position if air pressure is lost; the adjustable cushions only decelerate the piston near stroke end and do not act as a brake.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.