verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X355S

The AirTAC SE63 Standard Cylinder SE63X355S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 355mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke355 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$131.89 $139.39Save 5% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X355S

The AirTAC SE63X355S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. It delivers a robust 1559 N push force at 0.5 MPa, utilizing a 63 mm bore and a 355 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while leaving the integrated sensor grooves fully accessible on three sides.

Equipped with a built-in magnet (the -S option), this unit readily interfaces with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-stop deceleration via a set screw, effectively softening impacts at high cycling speeds rather than relying on a fixed rubber bumper.

Airtac SE63 Standard Cylinder SE63X355S Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X355S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke355 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X355S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×355Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X355S Is Used

packaging

Carton Erector Arms

Drives the folding mechanisms on continuous-motion packaging lines, utilizing the 1559 N push force to reliably square and seal heavy cardboard blanks at speed.

conveyor_belt

Pallet Diverters

Actuates routing gates on 63 mm belt conveyors, where the 355 mm stroke provides the extended reach needed to push full pallets onto secondary processing tracks.

factory

Injection Mold Ejection

Serves as a secondary knock-out actuator on mid-sized injection molding machines, using the adjustable cushion to gently decelerate the 20 mm rod before the mold face contact.

Is the Airtac SE63 Standard Cylinder SE63X355S the Right Cylinder?

When sizing this actuator, consider stepping down to the 50 mm bore if your load requires less force (982 N push at 0.5 MPa), or moving up to the 80 mm bore for heavier payloads (2513 N push at 0.5 MPa). Because the 355 mm stroke creates a long lever arm, unsupported side loads will induce severe bending moments on the 20 mm rod and front bearing; always pair this length with an external linear guide to prevent premature wear.

For retrofits, the standardized ISO 15552 mounting interface guarantees direct compatibility with other cylinders sharing the 63 mm footprint, utilizing standard PT3/8 ports and matching mounting hardware. Remember that this standard SE cylinder relies on live air pressure to move; it is not a rod lock, so loads will drift if air is exhausted or a valve centers.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X355S FAQ

The SE63X355S generates 1559 N of push force and 1402 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 2182 N. The absolute maximum push force is 318 kgf when operated at the maximum rated pressure of 1.0 MPa.

Yes, the SE63X355S is dimensionally interchangeable per the ISO 15552 standard, meaning it shares the exact same mounting footprint, port sizes (PT3/8), and rod thread (M16x1.5) as equivalent profile cylinders, allowing for a seamless direct replacement.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X355S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X355S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.