
The AirTAC SE63 Standard Cylinder SE63X360S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 360mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X360S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding automation. It provides a robust 1559 N push force at 0.5 MPa and a 360 mm stroke, utilizing a PT3/8 port and a 20 mm hard-chrome rod. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while retaining high structural rigidity.
This specific unit includes a built-in magnet (-S) for seamless integration with AirTAC CMSE reed and DMSE electronic position sensors across its three sensor grooves. To protect payloads during high-speed cycling, field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw rather than relying on a fixed rubber bumper.
| Model | Airtac SE63 Standard Cylinder SE63X360S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 360 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×360 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1559 N extend force to push heavy pallets onto perpendicular conveyor lines without stalling mid-stroke.
Relies on the 360 mm stroke and adjustable end cushions to smoothly fold large corrugated cardboard flaps at high cycle rates.
Secures heavy cast iron workpieces inside machining centers, leveraging the 20 mm rod to handle high side-loading forces.
When sizing this 63 mm bore actuator, evaluate your exact force requirements: the 50 mm neighbor provides 982 N push at 0.5 MPa, while the 80 mm neighbor steps up to 2513 N, allowing you to scale up or down based on your actual load. Note that a standard SE cylinder cannot hold a load vertically if air pressure drops or the valve centers; the piston will drift, so integrate a BSE rod lock or external check valve for fail-safe position holding. Furthermore, at 360 mm of stroke, the unsupported rod length increases susceptibility to side-load bending at the front bearing; always use an external linear guide to prevent premature seal wear and rod deflection. As a dimensionally interchangeable ISO 15552 component, it serves as a direct retrofit for other ISO 15552 cylinders, sharing standard mounting accessories like FA front flanges or TC center trunnions.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder generates 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N. The maximum allowable push force is 318 kgf at 1.0 MPa.
Yes, the SE63X360S is a true ISO 15552 profile cylinder, making it dimensionally interchangeable with other ISO 15552 cylinders. It shares standardized mounting dimensions and uses a PT3/8 port. The built-in magnet (-S) works specifically with AirTAC CMSE reed and DMSE electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.