
The AirTAC SE63 Standard Cylinder SE63X375 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 375mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X375 is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 1559 N of push force at 0.5 MPa and 2182 N at 0.7 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while maintaining the standardized VDMA 24562 interface.
Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed 375 mm strokes. Note that this specific SKU lacks a built-in magnet, meaning it is not wired for AirTAC CMSE or DMSE position sensing out of the box.
| Model | Airtac SE63 Standard Cylinder SE63X375 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 375 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×375 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folding mechanism on continuous-motion carton erectors, using the 1559 N push force to cleanly crease heavy cardboard flaps at speed.
Actuates a routing diverter on a 375 mm arc across a busy packaging conveyor, physically pushing pallets onto a secondary spur line without binding.
Indexes the tool carousel on a machining center, relying on the adjustable end cushions to safely stop a heavy tool holder assembly without shock loading.
At 318 kgf maximum thrust, this 63 mm bore sits perfectly between the 50 mm (982 N push @0.5 MPa) and the 80 mm (2513 N push @0.5 MPa) options, allowing you to scale power up or down depending on payload limits. Because the 375 mm stroke creates a long lever arm, side loads will induce bending moments on the Ø20 mm rod and front bearing; always support the load with an external guide to prevent premature wear.
As a true ISO 15552 cylinder, the SE63X375 serves as a direct replacement for other ISO 15552 profile cylinders, sharing identical mounting footprint and PT3/8 port locations. Remember that the double-acting air cushion only decelerates the piston near stroke end—it does not lock or hold the load if air pressure is lost.
Quick checklist
The SE63X375 delivers 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum push of 318 kgf at 1.0 MPa. It uses a PT3/8 port and a Ø20 mm rod with an M16x1.5 thread.
No. The SE63X375 is a standard double-acting cylinder; the adjustable air cushions only decelerate the piston near the stroke ends and do not act as a brake. If you need to hold a vertical load without live air pressure, consider the AirTAC BSE rod-lock variant or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.