
The AirTAC SE63 Standard Cylinder SE63X375S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 375mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X375S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver a robust 1559 N push force at 0.5 MPa. Driven by a 63 mm bore and a 375 mm stroke, it operates efficiently between 30-800 mm/s using a PT3/8 port. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Because this configuration includes the -S option, an internal magnet is fitted for non-contact position detection using AirTAC CMSE reed or DMSE electronic sensors. The cylinder relies on field-adjustable pneumatic cushioning at both ends, allowing technicians to tune the end-of-stroke deceleration via a set screw to eliminate hard mechanical impacts.
| Model | Airtac SE63 Standard Cylinder SE63X375S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 375 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×375 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Leverages the 1559 N extend force and 375 mm stroke to push heavy wooden pallets cleanly across transfer lines without stalling.
Uses the -S magnet with DMSE sensors to verify the full 375 mm extension when squaring large corrugated cartons prior to sealing.
Deploys the adjustable end cushions to decelerate the 20 mm rod smoothly when ejecting dense plastic parts from molding machines.
When sizing this actuator, compare its 1559 N push at 0.5 MPa against adjacent bores: stepping down to a 50 mm bore yields 982 N, while stepping up to an 80 mm bore provides 2513 N. To secure an exact ISO 15552 replacement, match the 63 mm bore, 375 mm stroke, PT3/8 port thread, and your required mounting accessory. If your sequence demands position feedback, specify the -S magnet to enable CMSE or DMSE switches.
With a 375 mm stroke, the 20 mm piston rod experiences increased bending moments under heavy lateral loads; an external guide rail should be installed to prevent rod-bearing wear. Note that a standard double-acting cylinder drifts when air pressure is lost or the valve centers—if the mechanism must hold a load statically without live pressure, integrate an external rod lock or evaluate the BSE series.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with an absolute maximum push capacity of 318 kgf at 1.0 MPa. It operates at speeds of 30-800 mm/s.
Yes, the SE63X375S is dimensionally interchangeable per ISO 15552. You can drop it directly into existing mounting hardware matching the 63 mm bore footprint, provided you maintain the PT3/8 port thread and standard stroke length.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.