
The AirTAC SE63 Standard Cylinder SE63X425S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 425mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X425S is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver a 1559 N push force at 0.5 MPa. Driven by a 63 mm bore and a 425 mm stroke, it operates efficiently between 30-800 mm/s using a PT3/8 port. The square extruded aluminum barrel omits external tie rods, yielding a smooth, corrosion-resistant exterior that mounts flush against machine frames while retaining high structural rigidity.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-cap deceleration via a set screw, effectively softening hard mechanical stops during high-velocity cycles.
| Model | Airtac SE63 Standard Cylinder SE63X425S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 425 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×425 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Routes heavy PET bottle traffic on high-speed packaging lines using the 1559 N push force and 425 mm stroke to actuate heavy routing gates reliably.
Indexes raw bar stock into CNC turning centers, utilizing the 425 mm travel distance and the CMSE/DMSE magnet sensors to confirm stock position.
Positions sheet metal backgauge stops on press brakes, where the adjustable end cushions absorb the kinetic energy of heavy gauging fingers at 800 mm/s.
When sizing this 63 mm bore actuator, evaluate your exact thrust requirements: stepping down to the 50 mm bore yields 982 N of push at 0.5 MPa, while stepping up to the 80 mm bore provides 2513 N. The 425 mm stroke on this Ø20 mm rod requires careful attention to side loads; for long unsupported extensions, integrating an external guide rail prevents rod-bearing bending and premature seal wear.
As a dimensionally interchangeable ISO 15552 component, it serves as a direct retrofit for other ISO 15552 profile cylinders, matching the 63 mm bore, 425 mm stroke, PT3/8 port, and standard mounting footprint. Note that a standard SE cylinder relies on live air pressure to hold a load; if your process requires position holding upon air loss, consider the BSE rod-lock variant.
Quick checklist
At 0.5 MPa, the push force is 1559 N and the pull force is 1402 N. At 0.7 MPa, the push force is 2182 N. The maximum push force is 318 kgf at 1.0 MPa.
Yes. The SE63X425S is dimensionally interchangeable per ISO 15552 standards, matching the 63 mm bore, 425 mm stroke, and PT3/8 port interface for seamless retrofitting without altering existing mounting hardware.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.