
The AirTAC SE63 Standard Cylinder SE63X450FTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 450mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X450FTC is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 1559 N of push force at 0.5 MPa and 2182 N at 0.7 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly against machine frames while integrating the standardized ISO 15552 footprint for direct retrofitting.
This 63 mm bore unit travels a 450 mm stroke on a 20 mm hard-chrome piston rod with an M16x1.5 thread. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration via a set screw, preventing harsh impact when cycling at speeds up to 800 mm/s. Note that this specific SKU lacks a built-in magnet, so it does not support CMSE or DMSE electronic position sensing without modification.
| Model | Airtac SE63 Standard Cylinder SE63X450FTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 450 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a heavy routing gate on a 1200 mm wide packaging conveyor, utilizing the 1559 N push force at 0.5 MPa to reliably pivot loaded pallets without stalling.
Pushes raw bar stock through a spindle bushing with a 450 mm stroke, relying on the FTC flange to maintain rigid alignment against the spinning material.
Drives a mechanical folding arm on a high-speed carton erector, using the field-adjustable air cushion to soften the end stop and prevent tearing heavy double-wall cardboard.
When sizing this 63 mm bore class, stepping down to the 50 mm bore reduces your 0.5 MPa push capability to 982 N, while stepping up to the 80 mm bore increases it to 2513 N. Because this model features an FTC mounting accessory, it provides a rigid flange interface ideal for absorbing heavy lateral moments along the 450 mm stroke. At 450 mm of travel, the 20 mm rod and internal bearing face elevated bending loads; an external guide rail is strongly recommended to prevent premature seal wear and rod deflection.
As a standard double-acting cylinder, the SE63X450FTC relies on continuous air pressure to hold its position. If air is exhausted or the valve centers, the piston will drift and cannot support a suspended load. For applications requiring true mechanical locking during an air loss or emergency stop, consider the BSE series rod lock variant. This base SE cylinder uses PT3/8 ports and serves as a dimensionally interchangeable direct replacement for any ISO 15552 cylinder with matching stroke and port specifications.
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N. The maximum drive force is 318 kgf, achieved at the 1.0 MPa operating pressure limit.
No, the SE63X450FTC is a standard double-acting cylinder and will drift if air is exhausted or the directional valve is centered. The adjustable air cushion only decelerates the piston near the stroke ends and does not function as a mechanical brake. For position holding, an external pilot-operated check valve or a BSE series rod lock cylinder is required.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.