
The AirTAC SE63 Standard Cylinder SE63X50FTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 50mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X50FTC is a double-acting, single-rod ISO 15552 profile cylinder with a 63 mm bore and 50 mm stroke. It generates 1559 N of push force and 1402 N of pull force at 0.5 MPa, making it well-suited for mid-range industrial pressing and lifting tasks. The extruded aluminum barrel lacks external tie rods, keeping the body smooth and corrosion-resistant for flush mounting in tight machinery frames.
This specific SKU is configured with an FTC center trunnion mounting accessory, allowing the cylinder to pivot freely during articulation. It uses a PT3/8 port and a Ø20 mm piston rod with an M16x1.5 thread. Because this model lacks the -S magnet option, it cannot host CMSE or DMSE position sensors without modification, relying instead on external travel limits for stroke confirmation.
| Model | Airtac SE63 Standard Cylinder SE63X50FTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Delivers 1559 N of extend force at 0.5 MPa to press bronze bushings into transmission housings on automated assembly lines.
Uses the FTC trunnion mount to pivot a routing gate smoothly on a packaging conveyor, accommodating angular load shifts.
Actuates a mechanical folder arm at 50 mm stroke to tuck top flaps on corrugated shipping cartons prior to sealing.
When sizing this 63 mm bore actuator, evaluate your pressure requirements against its 1559 N push at 0.5 MPa. If your application demands less force, stepping down to the 50 mm bore yields 982 N of push, while moving up to the 80 mm bore provides 2513 N, giving you a wide scaling window. The FTC center trunnion is ideal for mechanisms where the load vector changes angle through the stroke arc.
Remember that a standard SE cylinder cannot hold a load if air pressure is lost or the valve is centered; the piston will drift. If your fixture requires mechanical locking without live pressure, consider the BSE rod-lock variant. For this 50 mm stroke, side-load stress on the rod bearing is minimal, but any articulating trunnion setup still necessitates a well-aligned external guide to prevent premature seal wear.
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force reaches 2182 N. The maximum push force is 318 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE63X50FTC is dimensionally interchangeable per the ISO 15552 / VDMA 24562 standard, meaning it shares the exact mounting footprint and interface dimensions with other ISO 15552 profile cylinders. Note that this specific FTC-mounted SKU lacks a built-in magnet, so it will not trigger CMSE or DMSE electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.