verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X515

The AirTAC SE63 Standard Cylinder SE63X515 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 515mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke515 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$156.76 $164.26Save 4% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X515

The AirTAC SE63X515 is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. It delivers a robust 1559 N push force at 0.5 MPa alongside a 1402 N retract force, utilizing a 63 mm bore and a 515 mm stroke. Built to VDMA 24562 standards, it provides seamless dimensional interchangeability for plant upgrades without custom brackets.

This unit features a clean extruded aluminum barrel without external tie rods, which prevents debris buildup and simplifies flush mounting. The field-adjustable air cushioning at both ends allows technicians to dial in end-of-stroke deceleration, softening hard impacts at high cycle rates. Note this specific SKU lacks a built-in magnet, so it does not support CMSE or DMSE position sensing without modification.

Airtac SE63 Standard Cylinder SE63X515 Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X515
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke515 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X515

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×515Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X515 Is Used

packaging

Carton Erector Arms

Drives the folding mechanisms on continuous-motion carton erectors, using the 1559 N push force to cleanly crease heavy corrugated board over a 515 mm travel.

conveyor_belt

Pallet Diverters

Actuates diverter arms on 50 mm transfer conveyors, relying on the adjustable pneumatic cushion to softly index pallets without jarring the chain drive.

straighten

Press Brake Backgauge

Positions the backgauge finger on light-duty press brakes, where the ISO 15552 dimensions allow direct retrofitting into existing tooling layouts.

Is the Airtac SE63 Standard Cylinder SE63X515 the Right Cylinder?

When sizing this actuator, compare its 1559 N push at 0.5 MPa against the 50 mm bore (982 N push) if your load requirements drop, or step up to the 80 mm bore (2513 N push) for heavier machinery. Because the 515 mm stroke exceeds the 300 mm threshold, the 20 mm rod and bearing are subject to bending under side loads; an external guide rail is recommended to prevent premature seal wear. Remember that the air cushion only decelerates the piston near stroke end and will not hold a vertical load if air pressure is lost—consider a BSE rod lock for fail-safe holding. As a standard ISO 15552 cylinder, it shares mounting footprints and PT3/8 ports with equivalent profile cylinders.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X515 FAQ

The SE63X515 features a 63 mm bore with a PT3/8 port. It generates 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum push of 318 kgf at 1.0 MPa.

Yes, the SE series is dimensionally interchangeable per ISO 15552 and VDMA 24562 standards. You can drop it into existing mounts, but note this specific SKU lacks the -S magnet, so it will not trigger CMSE or DMSE sensors if your old machine relied on them.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X515

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X515 and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.