
The AirTAC SE63 Standard Cylinder SE63X585 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 585mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X585 is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 63 mm bore and a 585 mm stroke. It generates 1559 N of push force at 0.5 MPa and 1402 N of pull force, utilizing a PT3/8 port and a 20 mm hard-chrome steel rod. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while retaining the standardized ISO 15552 footprint for seamless retrofits.
This unit relies on field-adjustable pneumatic cushioning at both ends to decelerate the piston near stroke limits, allowing technicians to fine-tune end-stop impact via a set screw. Because this specific SKU lacks the -S magnet code, it is not equipped for AirTAC CMSE or DMSE position sensing out of the box. The 585 mm stroke falls within the standard made-to-order range for this bore, ensuring rapid availability without compromising the 30-800 mm/s speed capability.
| Model | Airtac SE63 Standard Cylinder SE63X585 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 585 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×585 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folding mechanism on a case erector, using the 1559 N push force at 0.5 MPa to reliably close heavy cardboard flaps over a 585 mm travel distance before tape application.
Positions sheet metal backstops on a CNC press brake, where the adjustable end cushions absorb the rapid 30-800 mm/s deceleration and the ISO 15552 body ensures rigid, deflection-free mounting.
Transfers heavy wooden pallets between adjacent roller conveyors, utilizing the 318 kgf maximum thrust to overcome sliding friction across the extended 585 mm stroke.
When sizing this 63 mm bore actuator, evaluate your force margins: stepping down to the 50 mm bore reduces your 0.5 MPa push to 982 N, while stepping up to the 80 mm bore increases it to 2513 N. If your mechanism must hold a vertical load without continuous air pressure, note that a standard SE cylinder will drift when air is exhausted or a valve is centered; you should integrate an external pilot-operated check valve or pivot to the BSE rod-lock variant for secure positioning.
For a 585 mm stroke, the 20 mm rod and M16x1.5 thread carry substantial side-load capacity, but the extended unsupported piston travel creates rod-bearing bending risks. To prevent premature seal wear and guide failure, implement an external linear guide to absorb lateral forces rather than relying on the cylinder itself. As a dimensionally interchangeable ISO 15552 component, it matches standard mounting accessories and port layouts (PT3/8) for direct replacement.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
The SE63X585 generates 1559 N of push force and 1402 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 2182 N. The maximum push force is 318 kgf when operating at the 1.0 MPa pressure limit.
Yes, the SE63X585 is a true ISO 15552 / VDMA 24562 profile cylinder, making it dimensionally interchangeable with other ISO 15552 cylinders. It shares the same mounting interface and PT3/8 port locations, allowing a direct retrofit without modifying your existing machine framework.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.