
The AirTAC SE63 Standard Cylinder SE63X65S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 65mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X65S is a double-acting single-rod profile cylinder that delivers a 1559 N push at 0.5 MPa across its 65 mm stroke. Built to the ISO 15552 standard, its extruded aluminum body omits external tie rods, yielding a flush, corrosion-resistant exterior that mounts cleanly in tight machinery spaces.
This specific unit includes the -S magnet for position sensing, pairing directly with AirTAC CMSE reed or DMSE electronic switches fitted into the body's three integral sensor grooves. Field-adjustable air cushions at both ends allow you to fine-tune end-of-stroke deceleration, protecting the mechanism from hard impacts during high-speed cycling.
| Model | Airtac SE63 Standard Cylinder SE63X65S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 65 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×65 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 1559 N of clamping force at 0.5 MPa to secure aluminum engine blocks during high-speed CNC machining operations.
Uses the precise 65 mm stroke and integrated DMSE sensor signaling to fold corrugated carton flaps cleanly before the sealing station.
Actuates a routing gate on a packaging conveyor, leveraging the adjustable cushion to softly stop the 63 mm bore without mechanical shock.
Stepping down to a 50 mm bore drops the 0.5 MPa push to 982 N, while stepping up to an 80 mm bore raises it to 2513 N, letting you scale thrust precisely to the load. Because the 65 mm stroke is short, side-loading on the 20 mm rod is minimal, though external guides remain best practice for rigid payloads.
As a true ISO 15552 profile cylinder, this 63 mm bore, 65 mm stroke, PT3/8 ported model is dimensionally interchangeable with other ISO 15552 units for direct retrofits. Note that a standard SE relies on live air pressure to move and hold; if the air supply drops, the piston will drift and cannot lock a vertical load.
Quick checklist
At 0.5 MPa, the push force is 1559 N and the pull force is 1402 N. At 0.7 MPa, the push increases to 2182 N, with a maximum push of 318 kgf at 1.0 MPa. The model includes a built-in magnet (-S) designed to trigger AirTAC CMSE reed and DMSE electronic sensors.
Yes, its standardized ISO 15552 mounting dimensions allow it to direct replace comparable profile cylinders. However, it is a standard actuator, not a rod lock; if air pressure is lost, the cylinder cannot hold a load and will drift. For position holding, consider the BSE series.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.