
The AirTAC SE63 Standard Cylinder SE63X680S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 680mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X680S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. It delivers a robust 1559 N push force at 0.5 MPa and features a 680 mm stroke. Because this stroke exceeds the standard 1500 mm maximum for a 63 mm bore, it is manufactured as a made-to-order unit to support extended travel requirements.
This actuator utilizes an extruded aluminum barrel without external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight spaces. The integrated -S magnet enables position detection with AirTAC CMSE reed or DMSE electronic sensors, while field-adjustable air cushioning at both ends allows you to fine-tune end-of-stroke deceleration to prevent hard impacts at high cycling speeds.
| Model | Airtac SE63 Standard Cylinder SE63X680S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 680 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×680 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 680 mm stroke and 1559 N push to extend and redirect heavy timber pallets between parallel conveyor belts in a packaging facility.
Drives the folding arms on a high-speed carton erector, relying on the -S magnet and DMSE sensors to verify full extension before glue application.
Pushes stamped metal door panels out of a forming die, utilizing the adjustable air cushion to soften the 2182 N impact force at 0.7 MPa upon retraction.
Selecting the SE63X680S is appropriate when your application requires a 680 mm stroke with a 1559 N push at 0.5 MPa. If you need less force, stepping down to the 50 mm bore provides 982 N push, whereas stepping up to the 80 mm bore yields 2513 N push for heavier loads. Keep in mind that a plain SE cylinder will drift if air pressure is lost or a valve is centered; it cannot hold a load vertically without live pressure, so consider a BSE rod lock variant if static holding is required.
Because the 680 mm stroke creates a long unsupported rod, side-load forces can induce bending moments that stress the rod bearing. For this extended length, adding an external linear guide is strongly recommended to prevent premature wear. As a true ISO 15552 profile cylinder, this unit is dimensionally interchangeable with other ISO 15552 cylinders, allowing you to use standardized mounting accessories like FA front flanges or TC center trunnions for seamless retrofitting.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
The 63 mm bore generates a push force of 1559 N and a pull force of 1402 N at 0.5 MPa. At 0.7 MPa, the push force is 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. It features a PT3/8 port and an M16x1.5 rod-end thread.
Yes. The SE63X680S is built to the ISO 15552 / VDMA 24562 dimensional standard, meaning it is a direct replacement for other ISO 15552 profile cylinders. You can reuse existing mounting hardware and footprints without redesigning your machine plate.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.